Hoover Vacuums - Popular Questions, Answers, Tips & Manuals


The V belt will stay " loose" until you lower the handle. Try replacing the flat belt and that should work.

Hoover U6437-900... | 166 views | 0 helpful votes


There is a duct in the front of the water recovery tank that you remove to install the upholstery hose. If this duct is missing or not installed properly you will have no suction

Hoover SteamVac... | 226 views | 0 helpful votes


go to hover for the owners manual sounds like it might be a clogged internal filter stifling the normal flow of cooling air around the motor

Hoover Vacuums | 35 views | 0 helpful votes


Take it to your local vac shop for repair. They can help you. It needs to be serviced annually anyway to perform properly.

Hoover U5753-900... | 744 views | 0 helpful votes


Check the motor brushes as well as the on/off switch.

Hoover Vacuums | 188 views | 0 helpful votes


The plastic clips in the handle that hold the trigger may be broken. Take the handle apart and inspect this area closely

Hoover SteamVac... | 201 views | 0 helpful votes


Check the opening behind the floor brush for obstructions there.

Hoover U5018-900... | 50 views | 0 helpful votes


Hi Bill.
Try this link
www.manualslib.com

Hoover Vacuums | 30 views | 1 helpful votes


If it's only 4mounths old should be covered under warranty or sale of goods act not fit for use.

Hoover U5194-900... | 71 views | 0 helpful votes


The brush roller may be clogged with debris. If so, the belt will only slip until it burns through from friction.

Hoover Vacuums | 36 views | 0 helpful votes


  • Defective battery
  • Defective charger

Hoover Vacuums | 22 views | 0 helpful votes


Thermal fuse failed, motor brush gear stuck, switch failed, power cord...

You will need to dismantle it and check the circuit with a meter...

Hoover Vacuums | 34 views | 0 helpful votes


There is an idler pulley that takes up the slack in the V belt when you pull the handle back to vacuum. Make sure it is engaging properly and the V belt is installed correctly.

Hoover U6630-900... | 173 views | 0 helpful votes


It's possible the thermal reset is defective. It shuts the motor off if it gets hot. Remove the bag door and take the bag off, remove both filters and then turn the vacuum on, just leave it sit there with the motor running. This eliminates the bag or filters causing any airflow resistance. If it still shuts off after a few minutes it's likely the thermal reset is bad. Some vacuums have an external thermal reset button which can be replaced if necessary but on your model it is built into the motor and you must replace the motor. If the motor runs fine put the bag and the filter under the bag back in - (make sure the filter is clean and not restricting airflow) put the bag cover on then turn it on again. If it overheats and shuts off then you may have a clog on there somewhere restricting the airflow. If so check the power nozzle area, the hose coming from the power nozzle, the extension hose and wands for clogs or restrictions.

Hoover U6426-900... | 115 views | 0 helpful votes


hi helen.
that does not sound good.
you might have to open it up and have a look inside and see if anything has burned out.
or get some one to look at it for you.

Hoover Vacuums | 29 views | 0 helpful votes


Watch this video on youtube that I found, it shows a brushroll repair but it also shows the bottom plate removed and should be helpful!
Hoover Dial Matic Model 1120

Hoover Vacuums | 29 views | 0 helpful votes

Not finding what you are looking for?
Hoover Logo

7,198 questions posted

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18408 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1467 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...