Hitachi Power Tools Saws - Recent Questions, Troubleshooting & Support

Its not too difficult: 1) There are 2 retainer pins located on the rear slide support (#4 on breakdown) - carefully drive these out with a punch - be careful to support the bracket so you don't break it. 2) remove the rear support and slide the saw head and arms out of the bearing. 3) Remove the 2 covers (front and rear) over the bearing 4) loosen the allen head set screw on the housing that holds the bearing in place 5) using a large socket and a plastic hammer - gently tap out the old bearing. Reverse process to replace. Do not use grease or oil on the bearing or slides - use a pure, clear silicone spray that dries completely - grease & oil attract & hold dirt and debris and will cause bearing failure. Hitachi C8FB2 8 1 2 Twin Rail Sliding Compound Miter Saw Parts

It sounds like your switch has a short circuit. It is quite unusual for this to happen and due to the nature of the fault I would highly advise not using the saw until it is sorted. If you are uneasy about working on the electrical parts of this you can find your nearest service agent on their website. Hitachi service page, put ypur postcode in the box on the top right.

Go to the Hitachi website, http://www.hitachipowertools.com/index.aspx, and under 'Service & Support' you can search by your zip code to find a service center near you. If it's the newer LXT line of tools it is now covered by a lifetime warranty so look for an Authorized Service Center to check on that.

If the fuel in it is 2 or more months old dump it out and put in fresh fuel and try statring. Also try try a squirt of starting fluid into the carb. If it fires on it you may need to do this a few times to pull the old fuel in the lines through till the fresh fuel can get to the carb.

closes I could find.copy and paste.https://www.carbatec.com.au/documents/manuals/Carbatec/Bandsaws/SW-1401-manual.pdf

Question edited for clarity, 'make model (what it is)', in full. No manual, just parts. Try black and Decker direct. https://www.google.com/search?q=black+and+decker+9443+bandsaw+manual https://support.blackanddecker.com/hc/en-us/p/all_locations ..

@Brian AndersonIt is better to write a new question rather than tagging an unsolved question from 10 years ago. It is now stuck on the Homepage as 'Pinned' and still showing Unsolved! :>Dhttps://www.google.com/search?q=+Dewalt+DW936+remove+the+guard+assembly..

It should be an issue of calibration, but no one else has experienced this issue. contact SCM Support direct. https://www.google.com/search?q=SCM+Nova+SI+400EP+Sliding+Table+Saw+calibration ..

https://www.manualslib.com/manual/1823573/Twin-Cut-Power-SawPlus.html?page=17#manual

Question edited for clarity, 'make model (what is is)'. Question moved from Washing Machines category. E1 Error, but not E.H1. https://www.google.com/search?q=Altendorf+WA80+error+code+EH1 Manual Errors and Troubleshooting. https://www.manualslib.com/manual/1583371/Altendorf-Wa-80.html?page=45 ..

..

How to use model number 84-6460

It may be this one by Sears under a different name. It shows bench adjustment parts via schematic. https://www.searspartsdirect.com/model/4upjq1jecw-003073/pro-tech-4002-table-saw-parts _A_ manual, not necessarily _THE_ manual https://c.searspartsdirect.com/mmh/lis_pdf/OWNM/L0604856.pdf https://www.google.com/search?q=Benchtop+10in+table+saw+05-30-13+%284002%29+manual ..

if keeps tripping breaker use multi to check plug wire or motor short

Question edited for clarity. Question moved from Computers. Nothing on them apart from people selling them. https://www.google.com/search?q=shopcraft+T6780-87 No manual, but any table saw manual with probably suffice. https://www.google.com/search?q=shopcraft+T6780+manual ..

1300 880 001 (Australia) or 0800 445 721 (New Zealand)

19651st May?5th January?Week 51?Ask the mystery maker.Full 'make model (what is is)' first 3 words in all questions please.It is all guesswork...