H&B Televison & Video - Recent Questions, Troubleshooting & Support
Divx, Xvid playback
sounds like your player dosen't like packed bitsreams. try unpacking with some software such as MPEG4Modifier or AVIdemux and see if that helps. Playback of packed bitstreams may also be jerky.
My dvd player note "nodisc" when i have a disc in the player
Just a completely "amature" guess, but last week I bought a "MEMOREX" DVD Lens Cleaner, that works great (shocked at how much dust it picked up! I didn't know they even existed). I bought it at the "Dollar Store" for ONLY $1.50 !! Also, especially if you have a dog or cat, take a peak inside the DVD tray area when it's open, with a decent $2.00 Dollar Store flashlight, and see if there are any pet hairs, dust, etc. visible. A longshot, but worth a look, no? Good luck!
47" plasma 1080p ... screen went black , sound
Plasma TV's have a shelf life. By that I mean the screen is only good for so many hours depending on the model. Most likely, you have burnt out the screen and the set will need to be replaced. The good news is, plasma TV's used to be better than LCD but that is no longer the case. You can get a very high quality LCD TV for a very low price now. Also they use a fraction of the power and don't generate all of the heat of a plasma.I'm sure this is not what you wanted to hear but the reality is that ALL plasma TV's do this eventually, and it is something that most salesmen back in the day didn't bother to tell customers. If you have an extended warranty, you may be able to get it replaced.
My plasma does not switch
Sounds like there may be a problem with your power supply or the main board in the TV.
On the bright side, this is usually repairable and it may be economically feasible to do so. Contact a local TV repair shop and obtain an estimate. If the estimate is over $300, I would recommend purchasing a new TV, as I've been selling 50' Plasma TVs for less than $600.
Samsang plasma t.v not working.will not switch on
The TV is on protect mode.
Try first leaving the TV power cord unplugged for some times, let say one hour or so.
Also
ensure that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem with no receiver box
or dvd connected.
If that does not work, and you keep having a flashing
led on front of the TV, and tv turning off by itself after a while,
that indicates a fault condition.
The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible reasons.
1The
internal circuits are jammed because of electrostatic
charges accumulating on capacitors, or because of a wrong voltage read
by the main chip on your monitor controller board. this started the
protection circuit.
2 The protection circuit detected a wrong
voltage or abroken contact, identified an internal fault and kicked in
, startingthe flashing light.
If you are in situation one, then theTV will reset just unplugging power cord for one or two hours,sometimes even minutes.
If you are in situation 2 , then there is an internal fault.
Common faults
that can occur are a blown capacitor on power board, a
convergence IC has blown, or a fault on Digital board.
Check also
the video cable or any external connection cable, if the cable is shorting, or the connector is bad, you
can get same flashing state because of the video cable.
If under warranty contact the manufacturer ringing the number on the user manual
If you want to repair at your own expenses, just locate any good qualified repairer.
My dvd freezes all the
Unfortunately the DVD is probably shot. The only thing you can do is get a DVD lens cleaner disk and use it. If that does not remedy the problem then there is a problem with the lens. It could be knocked a jar. This is a fixable problem, but cost as much as the unit to fix. DVD players are so cheap now its not worth buying any parts. If the player has been knocked or moved or dropped it is probably a miss aligned lens.
I had a DVD player that did the same thing. It wasn't worth trying to fix so I just bought a new one.
No sound on TV station
I buy a LCD panel H&B 30WS2. In my country the TV station use DK system whereas my TV have only BG and L system. I receive the image but not a sound. The audio decoder is "Micronas MSP3410G B8 V3" on the board "BEKO ZF7.190-01" . How can I solve this problem.
Thank you for your assistance.
Not finding what you are looking for?