CTX Computers & Internet - Recent Questions, Troubleshooting & Support
I am facing problem with my Samsung LCD monitor,
Try to do this: Just before the Windows start up screen (after the bios loading) press F8 and log in at safe mode settings. If at this mode you can see your screen change the resolution settings at a lower set. Save and reboot normally. Now try step by step to increase your resolution. In case of a blank screen appears at a new setting, don't do anything; after some seconds the monitor will come back to the previous settings. Save and go on.
In case of a problem or clarification, don't hesitate to post.
Thanks and regards
Please kindly rate this solution
Stelios
For the ctx s510ba to work does it have to be online
https://www.google.com/search?source=hp&ei=dLc1XsSKOsualwS5nIuACQ&q=For+the+ctx+s510ba+to+work+does+it+have+to+be+online&oq=For+the+ctx+s510ba+to+work+does+it+have+to+be+online&gs_l=psy-ab.3...1484.1484..2223...0.0..0.255.255.2-1......0....2j1..gws-wiz.avrp5RVpmTU&ved=0ahUKEwjElNG08rDnAhVLzYUKHTnOApAQ4dUDCAU&uact=5#kpvalbx=_d7c1XpKjKYqh1fAPmLiYkAs43
My Monitor Is Messed Up!!
A magnetic source next to the monitor will mess with the signal but that usually will only affect the side closest to the magnet, not both sides of the image. If it worked fine the last time you turned it on and is messed up now then most likely a capacitor went bad inside and there is no easy fix. If you are not experienced in electronics then it would be dangerous to open it up. Monitors contain high voltage inside that can be stored in capacitors even when the monitor is unplugged.
Ctx ezbook 700e larger HD
Why move it at all. XP needs SP3 to read hi capacity drives. I use USB external drives without any problems to increase capacity without the hassles of moving files. There are software packages that will transfer data from one hard drive to another if you must.
I have Ezbook PC-7.. Is it possible to upgrade
Hi.Apparently Microsoft are releasing evaluation (trial) versions of Windows Embedded Comapct 7 which is based on the Windows 7 environment and Windows Embedded POSready 7 also based on Windows 7.You can download either by clicking the link below. The normal version of Windows 7 cannot be installed on the netbook because the processer doesn't support it.If you don't want to download in trial the embedded versions then you will just have to keep on updating embedded 6.0 Pro and hope they fix the bugs with the system.LINK BELOW:
http://www.microsoft.com/windowsembedded/en-us/downloads/windows-embedded-downloads.aspxGood luck and regards.
The monitor turns off and on repeatedly.
I opened up and fixed a monitor just like this. The reason it only stays on for a second is because there are 4 or 5 bad capacitors on the power supply board that have over heated and gone bad due to cheap parts or poor ventilation. All I had to do was replace them and the monitor worked fine after that. Also i resoldered one joint on the bottom. While I dont reccomend the average home user to try this it is an extremely easy fix if you have the right tools.
CTX Panoview 630 Monitor
Panoview 630 Power Connector pinouts:
It has been many years since the question was posted but who knows, maybe this will help someone. Looking at the end of the connector clockwise from 1-oclock position:
1pm:NC
3pm:+12
5pm: no pin
7pm:+5V
9pm:+5V
11pm:GND
shield is GND
+5V@3A
[email protected]
(you can modify an Apple ADB cable to work)
Ezbook
??? freezes
If at boot??? ...it could be memory or lack thereof ...could be OS improperly installed. In fact it could be a plethora of software hardware problems
. Please be more specific with your questions and you get better answers. at best this is the best answer I can provide for you :)
Not finding what you are looking for?