Cisco Computers & Internet - Recent Questions, Troubleshooting & Support

Make sure that the subnet for the call manager is available over your VPN if you have locked the tunnel down. Also make sure that the IPC is allowed to bind to the VPN virtual network card.

Hope that helped!

If you are looking for a solution to recover EDB file into PST format then you can try Eseutil/R command provided by Microsoft in order to repair corrupted or damaged EDB file. In case if your trouble still remains same then you can go for a third party tool as there are plenty of options available over the net.

serch on :Fiberstore.com .all kinds of sfp transceiver module in Fiberstore .Tt is a fiber optic products online store. you can access to fiber optic transceiver directly.

There could be something stuck inside. Look inside and inspect to make sure there's no paper or anything else clogging in

Try hard-wiring your laptop to the router with an ethernet cable as a test and then try printing, if you do not loose connection to the internet then the problem is probably that the printing is hogging your wireless bandwidth.If the same thing happens with loosing connection to the internet try connecting to the internet real quick through another computer that is hardwired, you want to find out if the problem is a wireless one or that affects wired computers also. You might need a driver upgrade, you also might need to upgrade the firmware of the router

talk to CISCO on there official forum. real start here https://community.cisco.com/ why go anywhere else. as rules can be fluid , for sure if security gets more tight every day. talk to them , actual

Hi, Depending on the Supervisor Module model, most likely it's a standard Cisco's "password recovery procedure": Connect to the console Reboot the switch (power cycle) Start pressing Ctrl-C till you get to the BOOTROM Change boot configuration register to 0x2142 (confreg 0x2142) Boot the switch. It will ignore confuguration and boot "empty". Go to "enable mode". Copy startup configuration to running configuration ("copy start run") Change boot register back to 0x2102 (conf t -> conf 0x2102) Write config (write mem) Reboot Good luck, Mike / CCNP, CCDP, CCSP, CCVP Headset Adapters for office phone system

Yes they do support stacking. Here is the info sheet. Cisco Catalyst 2960 Series Switches Products Services

You can add LACP to your Cisco ethernet port config, and configure your Linux to support LACP.

You can find the instructions in the link ... Port Mirroring or Monitoring Cisco 857 Router Gkhan Tips

Make sure you set up correctly the subnet mask.

This is usually caused by a bad async controller where dc voltage is not supplied to the ports. There is nothing you can fix to make it pass the check.

these are the popular firewall for recent days: ·Packet filtering firewall ·Circuit-level gateway ·Stateful inspection firewall ·Application-level gateway (aka proxy firewall) ·Next-generation firewall

• Packet filtering - ...
• Stateful filtering - ...
• Routing support - ...
• Transparent firewall - ...
• AAA support - ...
• VPN support - ...
• Supports IPv6 - ...
• VPN load Balancing -

Keep your 4-port and just purchase a netgear or linksys 8-port switch. This will increase your port count to 12, but you burn two ports on uplinking. If you need more ports, just get a 16-port switch then. I believe this will be the most cost effective solution.

Hi'' as you have purchase a new one, uncover side of your unit then try to learn and have a diagram by copying in each where the all wires go '' or take a photo of it,''' thanks

Su mensaje no califica como una pregunta o consulta para un problema, intente en otro lugar NO HAGA ESTE SITIO CON SU BASURA Lleve su BASURA a otro lado Su mensaje califica como SPAM

Your message does not qualify as a question or query for a problem, try somewhere else DO NOT MAKE THIS SITE WITH YOUR GARBAGE Take your GARBAGE to another Side Your message qualifies as SPAM

Your message does not qualify as a question or query for a problem, try somewhere else DO NOT MAKE THIS SITE WITH YOUR GARBAGE Take your GARBAGE to another Side Your message qualifies as SPAM

ACURTNADA, Your message does not qualify as a question or query for a problem, try somewhere else DO NOT MAKE THIS SITE WITH YOUR GARBAGE Take your GARBAGE to another Side Your message qualifies as SPAM