Casio Computers & Internet - Recent Questions, Troubleshooting & Support
Wie kann ich die Casio TK 2300 umschalten auf Einzelbon
Um die Casio TK-2300 auf den Einzelbon-Modus umzuschalten, befolgen Sie bitte die folgenden Schritte:
- Dr?cken Sie die Taste "Programmierung", um das Programmierungs-Men? aufzurufen.
- Geben Sie das Passwort ein. Standardm??ig ist das Passwort "0000", es sei denn, es wurde zuvor ge?ndert.
- Dr?cken Sie die Taste "1" f?r den Registrierungsmodus.
- Dr?cken Sie die Taste "3" f?r die Bon-Einstellungen.
- Dr?cken Sie die Taste "1" f?r die Einzelbon-Einstellungen.
- W?hlen Sie "Einzelbon" aus, indem Sie die Taste "1" dr?cken.
- Dr?cken Sie die Taste "CA/AT/NS" (Clear All/All Tender/No Sale), um das Programmierungs-Men? zu verlassen.
Ihre Casio TK-2300 ist nun auf den Einzelbon-Modus umgestellt. Wenn Sie einen Artikel auf den Bon legen, wird ein Bon ausgedruckt, der nur diesen einen Artikel enth?lt. Wenn Sie weitere Artikel hinzuf?gen m?chten, wiederholen Sie den Vorgang.
Ich hoffe, das hilft Ihnen weiter!
Weird behaviour on my CASIO WK3500.
.This issue with your CASIO WK3500 keyboard could be caused by a few different things, including:
- Power supply issue: The issue could be with the power supply, and it may not be providing enough voltage to the keyboard when first plugged in.
- Circuit board problem: The issue could be with the circuit board within the keyboard, and it may not be able to start properly if there's a problem with the power supply.
- Firmware issue: There could be a firmware issue that is causing the keyboard to not start properly, which could be resolved by updating the firmware.
- Electrical interference: There could be electrical interference in the area that is causing the keyboard to behave erratically.
I am using Casio HR-150TM printing calculator (using electricity) When the figures are being keyed in, they are overlapping. Why? Please help.
There are a few potential reasons why the figures on your Casio HR-150TM printing calculator are overlapping:
- The paper roll may not be loaded correctly. Make sure that the paper roll is loaded correctly and that the end of the paper is properly aligned with the paper guide.
- The paper roll may be running low. Try replacing the paper roll with a new one.
- The print head may be dirty. Clean the print head with a dry cloth or a small brush to remove any debris.
- The ribbon may be worn out. Replace the ribbon if it appears to be worn out or damaged.
- The calculator may not be level. Make sure that the calculator is on a level surface to ensure proper printing.
- The calculator may be malfunctioning. If the above steps do not resolve the issue, the calculator may be malfunctioning. Contact the manufacturer or an authorized service center for assistance.
If the problem persist, it's recommended to check the user manual for troubleshooting steps or contact the manufacturer for further assistance.
Used wrong adapter to power my Casio pt 100
more, lots of PT-100 users long long ago and for decades did MODS.and the power pack mode was 2 ways or both ways1; wired center pin on some CASIO IS WIRED PER PHOTO BELOW. IF USING WRONG PACK IT BLOWS UP THE MOBO.2: added series diode 1N4001 up , to make it never blow up again. (voltage to high still will)I have a mod for #3 , too much voltage using zener diode and a fuse. ask.I have endless ideas on mods for most things that (plug in)the AD1 PACK MISSING AND WRONG PACK USED BURNS THIS KBD UP, AS VAST FOLKS IN THE NET TESTIFY.WRONG PACK OR CLONES SOLD WRONG, I SEE MANY SOLD THAT SHOW AD1 COMPAT, BUT IS A LIE.THEY LIE. NOW.WRONG VOLTAGE SOLD . WRONG POLARITY SOLD AND USED.WIRED WRONG, PACKS.THE PACK IS CALLED CASIO, AD1 (TOLD IN THE USERS MANUAL()MINUS -7.5 VDC AT 2.2WATTS (WATTS BE HIGHER IF YOU WANT)AMPS IS 0.133 amp max or 130mA , I bet the electronics inside uses 100mA max or less..
Casio PX700 sensors not working
Hi. I don't have a 700, but on the other privia's I have seen, there is a function key combo to turn on and off the touch response. Go to casio, and download the manual. You hit "fn" and then one of the lower keys. There are 4 levels of sensitivity on my machine. -Don
Not finding what you are looking for?