Bush Office Equipment & Supplies - Recent Questions, Troubleshooting & Support


For an E7 fault the PCB has to be reset:

1. With the door open, turn the appliance 'On'
2. Within 3 secs, push the program selection button 'P' 4 times
Good Luck Clive

See this: http://www.fixya.com/support/t25937477-error_codee7

Bush Office... | Answered on Jan 12, 2019


Back-light problem. Contact any service technician. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Surf the site with patience. Pull up older posts. Do a search by type in the brand name of your device at its search box. It will be best to replace the inverter board as card basis.
http://electronicshelponline.blogspot.com/

Bush Visions 32"... | Answered on Jul 17, 2014


Center Left and Center Right

Bush Office... | Answered on Aug 19, 2010


It might help if you would include name, model, and brand of what you are referring to

Office Equipment... | Answered 6 hours ago


Hahahaha okay .........! Pharmacy is the science and technique of preparing and dispensing drugs. ... It is a health profession that links health sciences with chemical sciences and aims to ensure the safe and effective use of pharmaceutical drugs.

Office Equipment... | Answered 12 hours ago


MORE THAN LIKELY YOU CAN NOT , AS NO ONE MAKES THEM . TOO CHEAP

Office Equipment... | Answered 16 hours ago


Error C3300 is a CCD Automatic Gain Control issue.

It could be poor contact in the connector terminals from the SHD PWB to the CCD PWB.

It is more likely a defective exposure lamp or inverter board that powers the lamp.

Try lifting up the Document feeder so you can see the optics frame through the platen glass and turning off and then on, the main power switch to see if the green exposure lamp illuminates.

A better, but more complicated way to check the lamp is to enter the service mode and run the exposure lamp test simulation. I will outline this procedure below. BE SURE NOT TO MESS WITH OTHER THINGS IN SERVICE MODE OR YOU COULD RENDER YOUR UNIT COMPLETELY UNUSABLE.

To Enter Service Mode:
Hit the "Status" button

Hit the following sequence on the numerical keypad:
1 0 8 7 1 0 8 7

You should be in service mode.

Use U601 by typing 6 0 1 and then "Start"

U601: Turning the exposure lamps on
Description: Turns the exposure lamp on.
Purpose: To check the exposure lamp.
Display:
CCD: Main Exposure Lamp
CID: Document Processor Exposure Lamp (inside the feeder)
Method
1. Press the start key.
2. Select the item.
3. Press the start key. The selected lamp lights.
4. To turn the exposure lamp off, press the stop key.
Completion
Press the stop key. The screen for selecting a maintenance item No. is displayed.

After checking the lamp(s) operation hit "reset" a few times to back out where you can type 0 0 1 "Start" to Exit Service Mode.

Office Equipment... | Answered 16 hours ago


If u have a very less number of plants...U may just spray the plants with a strong jet of water.

some of the toilet soaps will be effective.like the ones containing potassium or coconut oil. so, buy some hand soaps or shampoos, that contain these oils(also soyabean oil, fish, vegetable), make them as a mild liquid solution and spray on ur plants.

If u dont get one, combine ur homemade soap solution with the above mentioned oils and do the same.

Office Equipment... | Answered 18 hours ago

Not finding what you are looking for?
Bush Logo

10 questions posted

Ask a Question

Usually answered in minutes!

Top Bush Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4293 Answers

The Knight
The Knight

Level 3 Expert

76016 Answers

Terry
Terry

Level 3 Expert

8532 Answers

Are you a Bush Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...