Retail Supplies - Page 7 - Recent Questions, Troubleshooting & Support

These metal detectors will locate any metal with a conductive surface within 45-60 cm (18" to two feet) of the ground surface. A signal is heard because an electromagnetic field is generated and caused to flow out into space away from the search coil. Bounty Hunter Gold Digger Metal Detector Review Detectorly

Retail Supplies | Answered on May 03, 2018

You are probably using a decimal point. leave it out

Retail Supplies | Answered on May 03, 2018

That's usually caused by a clerk/ cashier programming issue. Check the codes for signing on. If you need a manual, this site has it listed -

Uniwell Retail... | Answered on May 03, 2018

It isn't a good idea to fully reset a register since you will lose the dealer programming which is more difficult. It is much easier to change the old programming to suit your shop. Then do Z reports to reset the old shop's reports

Retail Supplies | Answered on May 03, 2018

You haven't signed on. If the machine has had a PIN number programmed, you will need to program a new one. If you need a manual, this site has most -

Retail Supplies | Answered on May 03, 2018

Those buttons have been programmed with a different status. You can select PLU or Sub-department when programming an item. Change those buttons to the opposite one. If you need a manual, this site has one -

Retail Supplies | Answered on May 03, 2018

Make sure you use the release button to clear the paper error. Otherwise, do a half clear

Retail Supplies | Answered on May 03, 2018

Usually caused by corrupt data in your program. If the battery has not been replaced on time, it is very common.

Samsung Retail... | Answered on May 03, 2018

L in the display means the internal battery or batteries are low or missing

Retail Supplies | Answered on May 01, 2018

There is no specific code. You need to create one based on your needs, currency type, country etc. In the programming manual, you'll see the table for creating a MAC (init) code. Run through the table to create the code and then input it during the init process. If you don't have your programming manual, one of the users has it here:

Retail Supplies | Answered on May 01, 2018

This is very serious. It means the register is about to completely clear everything (or may have done so already). If it has been sitting for a long time without power, or new out of the box, then this is normal. We can try to jump it back out of the init mode.

Follow these steps very carefully:

Turn the power off at the wall.
Turn the key to PROGRAM mode.
Hold RECEIPT FEED button down.
Turn power on at wall.
When you see the display change to 'FFFFFFFFFF' let go of RECEIPT FEED.

Turn the key back to REG mode and try it. If you get error 8, then you may need to log a clerk back on.

Let me know if you have problems.


Casio Parts Cash... | Answered on May 01, 2018

Not a question that can be answered. What is a stopoder?

Retail Supplies | Answered on May 01, 2018

The metal detector does not expose you to ionizing radiation, e.g. x- rays, neither do the wands that are used for individual screening. Metal detectors operate by generating a low-intensity magnetic field that passes from one side of the detector to the other.

Retail Supplies | Answered on Apr 30, 2018

Your manual is here. I gave it a quick scan using the search for 'name'. I didn't see anything.

ER-A520 ER-A530 - Sharp
INTRODUCTION. Thank you very much for your purchase of the SHARP Electronic Cash Register, Model ER-A520/A530. Please read this manual carefully before operating your machine to gain a thorough understanding of the functions and features offered by this model ECR. Please keep this manual for future reference, ...

ER-A520 ' Cash Registers ' POS ' SHARP - SharpUSA > Electronic Cash Registers Home > Electronic Cash Registers > ERA520. ... The ER-A520 - robust features, reliability and quality. ... ER-A530.

Retail Supplies | Answered on Apr 29, 2018

The operation of metal detectors is based upon the principles of electromagnetic induction. Metal detectors contain one or more inductor coils that are used to interact with metallic elements on the ground. A pulsing current is applied to the coil, which then induces a magnetic field shown in blue. What is the Best Metal Detectorin 2017 Top Models Reviewed

Retail Supplies | Answered on Apr 28, 2018

Not finding what you are looking for?
Retail Supplies Logo

8,632 questions posted

Ask a Question

Usually answered in minutes!

Top Retail Supplies Experts


Level 3 Expert

1770 Answers


Level 3 Expert

79865 Answers

Patrick Tinashe...

Level 2 Expert

592 Answers

Are you a Retail Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides