Music - Page 6 - Recent Questions, Troubleshooting & Support


Check the power supply voltage and look for a hot component. If it takes a while to bring on the symptom it's probably something getting hot.

Fender Hot Rod... | Answered on Nov 19, 2017


the Heaviest string of each string pair is placed at the top (closest to your nose). In fact, if you look at the nut, (the notched thingy that spaces and holds the strings at the right spacing up by the tuning pegs) the notches in nut are wider than the paired string for this reason. That may not be true on all 12 strings but it is on mine. So the typical arrangement is heavy string, matching string. Heavy String, matching string. Except on the bottom 3 pairs where the actual string thickness can be the same. One caution note here....when tuning a 12 string, tune it a whole step lower. So rather than tuning it at EADGBE, tune it at DGCFAD then use a capo on the 2nd fret to bring the tuning up to EADGBE.
The reason for tuning a whole step lower is because on the top 3 pairs of strings you normally tune the thinner string an octave higher to give that 12 string sound. So if you start tuning at EADGBE, those thinner strings for the top EAD strings are going to be pretty tight and they will snap. So much safer to tune a whole step lower and just use a capo!!! Good Luck

Music | Answered on Nov 19, 2017


Try this link:
http://downloads.thesource.ca/421/4219634/Manuals/manual.pdf

Music | Answered on Nov 19, 2017


Do you have any pics of this guitar, a picture is worth a thousand words, this might help in the identifying of this guitar, if so just post them to this answer and I will see if I can help...

Gibson SG... | Answered on Nov 19, 2017


You need 3.5 mm Stereo Jack to 2 RCA cable.

Mackie Music | Answered on Nov 18, 2017


Does this guitar have a esonic 2 system, if so the other pickup is piezo pickup located under the saddle, there should be two wires coming from the pre-amp just remove the pre-amp from the body and make sure that the two wires are still plugged in and attached to the pickups, these are plugs like a small headphone style plug, just check these and the wires are held in by small wire clips,one of the wires may have came out of the clips...hope this helps I will look for a schematic for you and post it if I find one...Good Luck!!!

Epiphone Music | Answered on Nov 18, 2017


hi big eric.
this is all i could find on the internet.
see if this link helps you out.
Wiring diagrams for pre wired active bass guitar with 2 pickups and 5...

Bass Music | Answered on Nov 18, 2017


we can not not musical instrument appraisers here

The Music | Answered on Nov 16, 2017


archive.org/stream/OrganBlueBook-1985-1986.organforum.com/forums/showthread.php?2907-Kimball-Organ/OrganBlueBook1986-Pt.2#page/n65/mode/2up,.organservice.com/kimball/kimball.htm

The Music | Answered on Nov 16, 2017


If it's only on one speaker the first check if the cable from the amp to that speaker is not ripped off .Tru swopping the speaker around to the side which is working if it still has no so sound the maybe you should check on the amp to see if you did not cut the stereo down for that channel .See that the balance dial is in the middle. Last of the easy stuff to check is to take your headphones and see if you get even volume of both sides don't forget to check if there is a stereo/mono switch you want this switch to be set to stereo though the sound will no change much cause your bass may be a little lower on mono.When you have finally tested all of these and no satisfaction, then one of your transistors of that channel is blown. But it can also be a cap that is leaking or blown.You can open the amp but disconnect the power before touching or opening .Look at the channel which is not working to see if you have a cap swollen or blown then replace it with it's same value micro farad (pf).It's difficult to say what else can be wrong but those are the first to look at.It will take even me around a hour to say whats wrong .Fault finding is what takes time . good luck

Music | Answered on Nov 16, 2017


Your guitar was made at the Gibson Nashville Plant, TN, USA in either 1990 or 2000. Confusing eh? Gibson at times used the same serial number on different models in different years.

Music | Answered on Nov 15, 2017


Check Connections or Fuse !

Yamaha NP 30 76... | Answered on Nov 15, 2017


unplug both cords from the pedal when not playing !

Mtd Music | Answered on Nov 15, 2017

Not finding what you are looking for?
Music Logo

22,152 questions posted

Ask a Question

Usually answered in minutes!

Top Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Vito Vacirca Jr.

Level 2 Expert

140 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...