Heavy Machinery - Answered Questions & Fixed Issues


they get pressure from a common pump so have a hydraulic specialist check pump pressure as the pump shaft could be broken

Heavy Machinery | Answered 2 days ago | 20 views


My friend is a part time mechanic he gets his solutions from www.reliable-store.com
he gets from their every single detailed info, instructions etc. on all vehicles, and manuals like service, repairs, parts, owner's, op erations , maintenance etc.
U can get help from there
there is a girl at chat she can help you

Heavy Machinery | Answered on Jul 06, 2018 | 72 views


Robert green,
If your 7775 skidsteer, it will start will the help? right.. Weak battery, replace.. and check it will start...
with regards,
jaijith

Heavy Machinery | Answered on Jul 01, 2018 | 70 views


Look in your operators manual and do the calibration guide step by step. That will fix it.

Heavy Machinery | Answered on Jun 28, 2018 | 81 views


Have you baled with this baler before you put new belts on it? If not be sure all the belts are the right length, 444" , The belts should not be tight enough to turn without hay in the start up roll. When you start rolling a bale zig zag on the windrow, take care of the sides the middle will take care of itself. There was an update years ago of two 3/8 bolts and spacer for to belt tightner chains to keep the belts loose until there was enough hay across where the bale begins to tighten the belts and start rolling. You don't want the belts rolling with no hay in it. Will not roll straight.

Heavy Machinery | Answered on Jun 28, 2018 | 50 views


jasonraven8,
Buy a newhyraulic bleeding nipple and a hydraulicmanometer...
attach one end to hydraulic manometer and the other end to pump bleeding point.. you will get the reading...
with regards,
jaijith

bleeding cables-t1ohhdottlnks4fcccsz450j-1-0.jpg

hydraulic_manometer_pressure_gauge-t1ohhdottlnks4fcccsz450j-1-1.jpg

Heavy Machinery | Answered on Jun 26, 2018 | 90 views


If the tractor suddenly quit,the hydraulic pump shaft might have broken,( due to misalignment) with engine...
if the engine the pump must also runs.if it brakes entire system fails
hence the result.
contact..
with regards,
jaijith

Heavy Machinery | Answered on Jun 26, 2018 | 85 views


Robert,
Near the engine it is attached a hydraulic pump, to adjust the valve,
remove the lock nut near turn the valve clockwise, the pressure can be adjust with manometer..
manometer device is given in photo......'
with regards,
jaijith

hydraulic_manometer_pressure_gauge-t1ohhdottlnks4fcccsz450j-1-0.jpg

Heavy Machinery | Answered on Jun 26, 2018 | 119 views


Joseph Bartolovic,
If the hydraulic cylinder are not lifting there can be cause,
!) low oil quantity in the reservoir.
2) the cylinder seal fixing bolts are not in position inside the cylinder.
3) Adjust flow control in the system specified by manufacture.
with regards.
jaijith

Heavy Machinery | Answered on Jun 26, 2018 | 96 views


Dean,
First set the engine rpm as company recommended.. i.e.to keep maintain hydraulic pump pressure in the system,and if a short arises in the valve solenoid , this makes to remain close of the hydraulic pump valve ports and this makes to regret flow of oil to hydraulic motors to the wheels..
To rectify this problem
Remove defected solenoid valve with new....
with regards,

Heavy Machinery | Answered on Jun 26, 2018 | 80 views


Hey here you have not mention the name of your model. I know a website which provides all kinds of repair manuals. Have a look https://big-manuals.com/

Heavy Machinery | Answered on Jun 25, 2018 | 65 views


hey mate there is a website named big-manuals.com which provides all kinds of repair/user manuals at cheapest rates

Heavy Machinery | Answered on Jun 25, 2018 | 58 views


Any diesel will never start unless remove air inside the system....Remove slighty remove all the pipes connecting to the injector....when cranking air removes the system showing bubbles air pipe connectors.... after starting tight all the nut....then it will start,,,,make sure battery must be strong ....

Heavy Machinery | Answered on Jun 24, 2018 | 61 views


no power going to it most likely

Heavy Machinery | Answered on Jun 23, 2018 | 70 views


Dear,
The hindging point of the hydraulic cylinder and the steering can be the cause....also the "kingpin" of the stub axle get jammed . Make it free, this will work perfectly, Also lubricate the hindge point daily... this problem can be solved.
with regards and reply.

Heavy Machinery | Answered on Jun 19, 2018 | 77 views


Request the 47801 manual from Bolens.

Heavy Machinery | Answered on Jun 18, 2018 | 66 views


There should have been a separate manual for the Brigg's and Stratton engine that accompanied the user manual. That engine manual addresses oil and gas. I also suspect that the model number is 4265. At any rate, if there is no dip stick, it is likely you want the oil to the top of the fill hole. You can check by phone or chat the support for the chipper shredder if this has not assisted you. Click the link below.

http://www.troybilt.com/webapp/wcs/stores/servlet/DisplayOwnersManualList?storeId=10001&catalogId=14102&langId=-1&logoCode=02&modelNumber=CR4265&serialNumber=

Troy Heavy... | Answered on Jun 16, 2018 | 53 views

Not finding what you are looking for?
Heavy Machinery Logo

Ask a Question

Usually answered in minutes!

Top Heavy Machinery Experts

Bill Boyd

Level 3 Expert

51218 Answers

Daryl Gleaton

Level 3 Expert

742 Answers

Tom Chichester

Level 3 Expert

45036 Answers

Are you a Heavy Machinery Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...