Heavy Machinery - Page 2 - Recent Questions, Troubleshooting & Support

My friend is a part time mechanic he gets his solutions from www.reliable-store.com
he gets from their every single detailed info, instructions etc. on all vehicles, and manuals like service, repairs, parts, owner's, op erations , maintenance etc.
U can get help from there
there is a girl at chat she can help you

Heavy Machinery | Answered on Jul 06, 2018

Yes I have one in perfect condition with prints etc. and the original sale brochure!

Heavy Machinery | Answered on Jul 02, 2018

Robert green,
If your 7775 skidsteer, it will start will the help? right.. Weak battery, replace.. and check it will start...
with regards,

Heavy Machinery | Answered on Jul 01, 2018

Look in your operators manual and do the calibration guide step by step. That will fix it.

Heavy Machinery | Answered on Jun 28, 2018

Have you baled with this baler before you put new belts on it? If not be sure all the belts are the right length, 444" , The belts should not be tight enough to turn without hay in the start up roll. When you start rolling a bale zig zag on the windrow, take care of the sides the middle will take care of itself. There was an update years ago of two 3/8 bolts and spacer for to belt tightner chains to keep the belts loose until there was enough hay across where the bale begins to tighten the belts and start rolling. You don't want the belts rolling with no hay in it. Will not roll straight.

Heavy Machinery | Answered on Jun 28, 2018

Buy a newhyraulic bleeding nipple and a hydraulicmanometer...
attach one end to hydraulic manometer and the other end to pump bleeding point.. you will get the reading...
with regards,

bleeding cables-t1ohhdottlnks4fcccsz450j-1-0.jpg


Heavy Machinery | Answered on Jun 26, 2018

If the tractor suddenly quit,the hydraulic pump shaft might have broken,( due to misalignment) with engine...
if the engine the pump must also runs.if it brakes entire system fails
hence the result.
with regards,

Heavy Machinery | Answered on Jun 26, 2018

Near the engine it is attached a hydraulic pump, to adjust the valve,
remove the lock nut near turn the valve clockwise, the pressure can be adjust with manometer..
manometer device is given in photo......'
with regards,


Heavy Machinery | Answered on Jun 26, 2018

Joseph Bartolovic,
If the hydraulic cylinder are not lifting there can be cause,
!) low oil quantity in the reservoir.
2) the cylinder seal fixing bolts are not in position inside the cylinder.
3) Adjust flow control in the system specified by manufacture.
with regards.

Heavy Machinery | Answered on Jun 26, 2018

First set the engine rpm as company recommended.. i.e.to keep maintain hydraulic pump pressure in the system,and if a short arises in the valve solenoid , this makes to remain close of the hydraulic pump valve ports and this makes to regret flow of oil to hydraulic motors to the wheels..
To rectify this problem
Remove defected solenoid valve with new....
with regards,

Heavy Machinery | Answered on Jun 26, 2018

Hey here you have not mention the name of your model. I know a website which provides all kinds of repair manuals. Have a look https://big-manuals.com/

Heavy Machinery | Answered on Jun 25, 2018

hey mate there is a website named big-manuals.com which provides all kinds of repair/user manuals at cheapest rates

Heavy Machinery | Answered on Jun 25, 2018

Not finding what you are looking for?
Heavy Machinery Logo

2,093 questions posted

Ask a Question

Usually answered in minutes!

Top Heavy Machinery Experts

Bill Boyd

Level 3 Expert

51191 Answers

Daryl Gleaton

Level 3 Expert

742 Answers

Tom Chichester

Level 3 Expert

45018 Answers

Are you a Heavy Machinery Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides