Crafts & Hobbies - Page 8 - Recent Questions, Troubleshooting & Support


Try to find the Brushes that run the motor...You may have to remove the Body.... There are many variations to the Mounting some have Screws others have clips you push or pull Once the body is Off..look for the brushes.It will be a small square of Brass, and inside will be a spring and a block of Carbon with a wire attached,.. The Carbon Brush runs on the Brass section of the Motor with the spring holding it in... Both have a Covering Clip.

OK
Look at the covering clip first.. is it pushing hard enough against the Brush.... if notbend so it does... If it DOES... then take the briush out, and run the end that goes against the rotor on a fine file or sand paper... What you want here is to clean the tip

Once the tip is clean and th Spring Cover is set... replave everything and try again....

IF it does not work I would suggest taking it back to where you got it and ask them to fix it...
But I would guess this is your problem.....
One other thing.... While you had it apart, I would check everything, giving moving Parts a drop of oil...

Other than this I am not sure what to suggest.
The Pic is of a pair of Brushes so you know what you are looking for... I can give you Pics of other parts but not knowing exactly what motor it is... I could put you off track with it.

Good luck


hhbtm540bru-4tzlvtqcqle0rd1hcgftwv42-4-0.jpg

Crafts & Hobbies | Answered on Jan 22, 2018


I have small Drawing Boards... What I use to hold the Paper Are clips... These are about 1 inch or 25mm wide, flat on the Bottom with a Bent top... Slide the flat underneath at use the top to hold the Paper...

Sould be abe to get these for any Stationary Shop

Crafts & Hobbies | Answered on Jan 22, 2018


what type glue is it? if it is elmers hot water should do the trick

Crafts & Hobbies | Answered on Jan 21, 2018


I would try a hair dryer to see if it loosens. Could have crayon shavings in it.

Crafts & Hobbies | Answered on Jan 15, 2018


It depends on the machine the expression 2 the expression and the little machines use markers that fit into the blade housing slot. The explore machines use special markers put out by cricut or there are some called slick writers that fit in the accessory clamp.

Crafts & Hobbies | Answered on Jan 12, 2018


Hello, Jo -

From information I have found on other websites, apparently the Erbauer brand of tools are made by ScrewFix.

I found a ScrewFix Community Forum online with questions about Erbauer replacement parts. This is the link to the forum:
https://community.screwfix.com/threads/erbauer-replacement-parts.95804/
Read the questions and comments on both pages.

From that information it seems that ScrewFix and Erbauer provide no replacement parts.

Through the eBay resolution process you can probably have your purchase price refunded.

Crafts & Hobbies | Answered on Jan 11, 2018


Is this a baby blanket that you need to piece together? If so post a picture and maybe I can help. But otherwise I am not sure what kind of help you are asking for.

Crafts & Hobbies | Answered on Jan 11, 2018


Is the transformer getting hot? Sounds like there might be a short circuit in the system. You'd need to put an ohm meter across the tracks (or a Digital Multimeter (DMM) set to ohms) to verify the short and then look around for some electrical path between the tracks.

Crafts & Hobbies | Answered on Jan 09, 2018


You should switch to a size or two smaller needle when you switch yarns.

Debbie Bliss... | Answered on Jan 03, 2018

Not finding what you are looking for?
Crafts & Hobbies Logo

3,742 questions posted

Ask a Question

Usually answered in minutes!

Top Crafts & Hobbies Experts

R.A. Ellis
R.A. Ellis

Level 3 Expert

12706 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

22826 Answers

ray gallant

Level 3 Expert

54527 Answers

Are you a Craft and Hobby Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...