Crafts & Hobbies - Page 6 - Recent Questions, Troubleshooting & Support


I assume that you are talking about a narrow ledge, 15ft long. I don't think you would have a problem getting a train to go from one end to the other and then back up to its starting position. There are electronic circuits that do this. Had one for a Christmas trolley that ran through the town under the tree that did that.

Crafts & Hobbies | Answered on Dec 29, 2017


Remove the train from the track. use a multimeter to check the polarity along the length of the track. (Note POLARITY, not voltage). Depending on your setup there could be a section where the polarity is opposite in this section. Here the train will want to go backwards, and at the changeover point it will stop. If you just have a big circle with only one connection to the track then you have a real mystery.

Crafts & Hobbies | Answered on Dec 28, 2017


tenes que verificar la potencia del transformador, una ves hecho esto, suma las potencias que consumen el tren y

lionel Barrel Shed,

Si la suma no sobrepasa la potencia del transformador es posible alimentar las dos cargas.

Crafts & Hobbies | Answered on Dec 27, 2017


The 1026 has a bakelite shell. It is held in place by two tabs that snap over the metal frame. The shell is very fragile. However if you aren't a qualified tech with this sort of thing this tranformer is very inexpensive, rather than take a chance, I would just dump it. You can usually find them at shows for about five bucks.

Crafts & Hobbies | Answered on Dec 25, 2017


I still have not received my order as of today. Please check on this shipment! thank you,

Thomas S. Pyle
310 801 2416

Crafts & Hobbies | Answered on Dec 23, 2017


Look in the tunnel and see if there are any thin bits of metal that could be shorting it out. If it is a sectional track layout, unclip the section just before the tunnel and just after. Try this to all your sections. If there is a short, your train should work until you connect the bad piece to it then all will stop. Basically a process of elimination. Also check connections to the track to see if there is a single loose wire that may be causing the problem. Another thing is getting the power pack and connect it to a single piece of track which is not connected to the layout and try the train. It could be the train shoring it out, try the train and if it works, it's got to be the track..

Bachmann James... | Answered on Dec 22, 2017


Try it in both positions. The one that gives you smoke is the correct position.

Crafts & Hobbies | Answered on Dec 20, 2017


try using a squirt of furniture polish, it helps sticking buttons on xbox games controllers...

Crafts & Hobbies | Answered on Dec 19, 2017


If it the Dremel Versatip then it isnt wired as it is run by gas. I had the same problem - turned out the pezoignition system had failed. Replaced under warranty. No questions.

Dremel 1550:30... | Answered on Dec 19, 2017


The locomotive is not receiving the single from the remote . You need to paire them. In the Manuel should be intuitions for pairing. Hope this is some help.
REDEAGLE

Crafts & Hobbies | Answered on Dec 17, 2017


If you are powering that unit off and the light fades out when you do that. There is nothing wrong. The power supply changes AC from house current to DC and there are filters in the circuit that hold a charge and release it slowly when the power is shut down.

Polar Express... | Answered on Dec 17, 2017


How to Make a Custom Shirt with Your Cricut - Pretty Providencehttps://prettyprovidence.com/make-custom-shirt-cricut/Proxy Highlight
Jun 27, 2017 ... You can make custom DIY t-shirts so inexpensive when you use your cutting machine. ... If you're like me, you have a lot of inside jokes with family or friends and love custom shirts. I have spent SO ... I am just popping over here to share my Cricut expertise but typically blog at Practical and Pretty! I'm so ...

Crafts & Hobbies | Answered on Dec 16, 2017


HERE ARE SOME YOU TUBE LINKS THAT MIGHT HELP YOU

https://www.youtube.com/watch?v=1RIe4abOEvI
STANLEY DIDN'T REALLY DESIGNATE TYPES PER SAY, UNTIL THEY ACQUIRED BAILEY BACK 1860 OR ABOUT THAT TIME

https://www.youtube.com/watch?v=DT_GVYBtgpI

HOPE THIS HELPS A LITTLE

BEBE

Stanley Crafts &... | Answered on Dec 16, 2017

Not finding what you are looking for?
Crafts & Hobbies Logo

3,689 questions posted

Ask a Question

Usually answered in minutes!

Top Crafts & Hobbies Experts

R.A. Ellis
R.A. Ellis

Level 3 Expert

12273 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

20407 Answers

ray gallant

Level 3 Expert

51527 Answers

Are you a Craft and Hobby Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...