Car Audio & Video - Page 6 - Recent Questions, Troubleshooting & Support


If you still have the remote, you can try the basics, First try 012345 sometimes thats all it takes I know on my 9312 that will overide the rest of the radio and allow me into the sub menu to fiddle with the radio. if that dosent work then enter 00000, 11111, 99998, 55555 or something along those lines most default codes are as simple as that. if that dosen't work, you will need to contact the installer and see if they had put in an anti theft code, and find out if trhey keep records of it

Jensen VM9314... | Answered on Jun 05, 2018


i need to find the code to get my radio off of safe mode for a 1998 volkwagen golf?

Car Audio &... | Answered on Jun 04, 2018


Google 'radio code' with the make and model

Car Audio &... | Answered on Jun 04, 2018


to the guy who is looking for the wire diagram, you can buy a wire kit for the stereo connection for about $60 from best buy or some other place like that. your car's door ding and some other things wont work with out it. hope that helps you some.

Car Audio &... | Answered on Jun 04, 2018


penge po ako ng vip at ecoin 500000 pleassssssssssss

Crossfire VR404... | Answered on Jun 04, 2018


Make sure the red wire is still connected or make sure the red wire hasn't been severed. Also, check the fuses located in the engine compartment. The red wire connects accessory terminal in the fuse block. Also check the fuses in the cabin. This fuse box is typically located on the driver's side, at knee level, next to the door panel, and underneath the dashboard. As a last resort, the unit can be taken to an authorized or factory service center.

JVC AM FM CD DET... | Answered on Jun 03, 2018


as your sub is only rated to 400w rms simply connect the sub to either a or b channel outputs you may wish to use an rca splitter before the amp to feed both left and right audio channels into a single channel on the amp. WARNING connecting both channels on the amp to the sub will overload the sub and possibly blow it up so i highly recommend not doing so.

AudioBahn Car... | Answered on Jun 03, 2018


i was not able to locate a manual but i did find some interesting information that hopefully may help,
The AudioBahn AW1000X Car Subwoofer Features: dual 4-ohm voice coils, non-pressed pulp cone, huge foam surround, frequency response 23-500 Hz, power range 50-600 watts RMS (300 watts per coil), peak power handling 1,200 watts, sensitivity 91.1 dB, top-mount depth 5-1/4" ,sealed box volume: 0.4-.95 cubic feet, ported box volume: 1.632 cubic feet.

AudioBahn Car... | Answered on Jun 03, 2018


i'd need more info but from what you've stated, sorry to break it to you but it sounds likely you've incorrectly wired you speakers and blown your amp. this will prove no doubt an expensive mistake and learning exercise.

AudioBahn Car... | Answered on Jun 03, 2018


to drop the amp load to 1 ohm you need to divide the output signal path and the best way is by wiring a second woofer in parallel as seen in the ideal diagram attached this has the desired effect of doubling the volume .
since 2 ohm divided by 2 is 1 ohm load connected to your amp.
so the short answer is no you can't do that with a single woofer
2ohm low amp-vytae2j2uoxlsgotk4qtkzpd-5-2.png

AudioBahn Car... | Answered on Jun 03, 2018


sounds like a thermal overheat protect issue, sorry to break it to you but sadly the way most amps are built these days it's either not worth the cost of trying to repair or impossible to do so by hand. you'd be better off just getting a new amp

AudioBahn... | Answered on Jun 03, 2018


Generally there are 2 parts to this problem

part 1
input signal as these woofers are just subs remember to give them a low line in signal before the amp (see diagram) i like to use rca low pass crossover filters from harrison labs (see link)

part 2
is the wiring configuration of the 2 woofers by wiring them in parallel as shown in the diagram you reduce them to a 2 ohm load for your 2 ohm amp meaning you'll get max loudness and efficiency
2ohm low amp-vytae2j2uoxlsgotk4qtkzpd-5-0.png
Harrison Labs FMOD Inline Crossover Pair 100 Hz Low Pass RCA Shipping is...

AudioBahn Car... | Answered on Jun 03, 2018


unfortunately if you only have the one woofer there isn't really any safe way to do so but if you had a pair of woofers you could in theory wire them in parallel thus creating only a 3 ohm load but your amp must be able to work at such low ohms otherwise you WILL blow up your amp.

AudioBahn Car... | Answered on Jun 03, 2018

Not finding what you are looking for?
Car Audio & Video Logo

106,457 questions posted

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4944 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

79865 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...