Blade Saws - Recent Questions, Troubleshooting & Support


*before attempting to remove the blade, be sure the power source is either unplugged (if corded) or removed (if battery). If this is a latch style reciprocating saw, after disengaging the latch, give the end of the blade a few sharp taps with a mallet or hammer. then attempt to remove the blade by gloved hand, or adjustable pliers. if the blade is at all damaged during this process, throw it away and use a new blade next time. The blade housing may need to be blown out with some compressed air and the latch mechanism may need some lubricant. Hope this help!

Blade Saws | Answered on Nov 05, 2018


I am not familiar with the model so I don't know how the top comes off but usually they aren't held down by much.

Usually it only needs the plastic or aluminium insert to be removed to access the riving knife or to remove the blade.

A maladjusted riving knife is a common cause of a "catching" blade.

It is worth considering, when such saws arrive they usually need calibrating, which often means semi-dismantling the saw and rebuilding it with a higher degree of precision than the factory can muster - using a large trusted set square, an accurate blade height gauge, etc.
It is also worth considering many modern table saws also have an electric brake that is supposed to stop the blade in a couple of seconds when the power is switched off.

Blade Saws | Answered on Oct 30, 2018


Is the blade not true (flat)

Blade Saws | Answered on Oct 29, 2018


The manual indicates that there is a hole at the top of the handle and a screwdriver included with the jig saw. Insert the screwdriver in the hole and loosen the the set screw about 3 or 4 revolutions.

Blade Saws | Answered on Oct 27, 2018


return it to home depot and get another one, don,t fool with it. you have a 90day return policy. me I would it now and move on.

Blade Saws | Answered on Oct 26, 2018


since we do not have the machine we could not begin to know the length . try a good home improvement store like lowes or home depot

Blade Saws | Answered on Oct 25, 2018


Saw Bar Assembly
Part Number: 304944006
is a metal shaft with a plastic end that goes through a small collar.
The large split collar is about in the middle of the shsft

Blade Saws | Answered on Oct 07, 2018


If I remember correctly, there is an adjusting collar on the side of the blade. I think it also had a set screw that you had to use an allen wrench to loosen. (Dad didn't allow me to mess with his saw.)

Blade Saws | Answered on Oct 07, 2018


Perhaps the shaft between the motor and the blade is ground off to accept a very thin wrench or there might be a small hole from the bottom of the saw that will accept a thin rod to lock the armature from turning .BTW Most saws have a counter rotating screw that locks the blade (ie Tighten to loosen) Good luck. BTW you should mention what make and model saw it is since different manufactures have different methods of securing the armature.

Blade Saws | Answered on Oct 06, 2018


then go shopping at your local home improvement store

Blade Saws | Answered on Oct 02, 2018


sorry but you have stripped the drive gears

Blade Saws | Answered on Oct 02, 2018


sounds like you stripped the drive gears out of it

Blade Saws | Answered on Oct 02, 2018

Not finding what you are looking for?
Blade Logo

317 questions posted

Ask a Question

Usually answered in minutes!

Top Blade Saws Experts

Kenneth Walker

Level 2 Expert

270 Answers

Cindy Wells

Level 3 Expert

5641 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1995 Answers

Are you a Blade Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...