Belle Group Hammering - Recent Questions, Troubleshooting & Support
Pump troubleshooting
What you need to consider is horsepower not size. The horsepower requirement for a house is determined by the area of drainage connected to the sump, the depth to the groundwater, the depth of the basement, and a few other factors. A 1/3 hp pump is standard for most houses.
Fuel Pump how to
Things You’ll Need:
* Socket wrench
* Ratchet wrench with universal joints
* Screwdriver
* Pliers
Remove the Old
*
Step 1:
Disconnect the battery cables.
*
Step 2:
Relieve any pressure in the fuel tank by removing the fuel cap.
*
Step 3:
Unfasten the fuel lines from the pump. Be sure to wipe up any fuel that spills immediately.
*
Step 4:
Remove the bolts that are holding the pump onto the mount and remove the fuel pump.
*
Step 5:
Clean off any gasket residue that remains on the mating surface of the framework.
Install the New
*
Step 1:
Apply a layer of gasket sealer on both sides of the new gasket and put gasket over the bolts.
*
Step 2:
Install the new mechanical fuel pump onto the engine. The rocker arm of the pump needs to be against the eccentric inside of the engine.
*
Step 3:
Attach the fuel lines to the fuel pump. Reattach the lines to the carburetor. Use a wrench to make sure it is tight.
*
Step 4:
Reconnect the battery ground cable.
*
Step 5:
Start the vehicle and check for leaks.
Pump support
Follow these steps to replace a malfunctioning sump pump. If you are starting from scratch and want to put in a completely new sump pump and drain line, you should have a professional plumber do any actual piping unless you have an advaced knowledge of those techniques. Locate the sump pump in your basement. Unplug it to avoid possible electrical shock or personal injury. Find the place to disconnect the pump from the drain line. This is usually either a screw-together type union or a rubber coupling with hose-clamp fastenings. Both are quickly and easily undone. Remove the pump from the pit and allow it to drain for a few minutes. Any plastic piping or fittings that comes from the water outlet opening and goes up to where the pump connected to the drain line needs to be removed and saved to reattach to the new pump. Take the pump with you to your local hardware store, plumbing-supply house or home-improvement center. They can help you pick a replacement that requires the same power source and provides the same drain-line hookups and pumping capabilites. Reattach any piping and fittings in the same way that they were on the old pump. Set the new pump in the pit and reconnect the union. Plug in the pump. You can test the pump by filling the sump pit with buckets of water.
Breakers Troubleshootinf
When breaking oversize material the breaker is expected to break the material down the middle into two pieces. This is optimum production. If the operator has to re-position the breaker towards the edge of the rock and gradually downsize the material, production rate slows down. To assess what size of breaker will effectively handle this application, the size and hardness of the material must be known. If a 4 cu. yard piece of hard rock (20,000 psi or greater) needs to be broken in half you will require a 7,500-ft. lb. or larger breaker. If a 2 cu .yd. piece of limestone (20,000 psi or less) needs to be broken in half you will require a 3,000 - 5,000-ft. lb. breaker.
Breakers advice
When trenching, the breaker is expected to fracture a solid mass of rock into manageable pieces. The size of the material could be 100's of cu.yds, and the energy will be quickly absorbed. This is why it is recommended to work from a bench so the rock has somewhere to break out. We recommend when trenching in limestone or medium hard rock, to use a 3,000 - 5,000-ft. lb. breaker. When working in hard material we recommend a 7,500 - 10,000-ft.lb. breaker, and if high production is critical, a 13,500-ft.lb. breaker would be beneficial.
Kango 950 motor runs but hammer only engages sometimes
This is an indication that the hammer needs service. When you take the barrel off you will see the striker. There is a piston inside the striker, when the rubber rings on the piston wear out you have the problem you describe. time to replace the motor brushes clean and regressed, make sure to use the correct grease, Check the backlash on ring and pinions. Don't put too much grease on the piston or it will stick and not strike. Good luck I forgot to ask which version. This is for the uk atlas coco, silver with blue or red handle
5/29/2022 2:06:56 AM •
Hammering
•
Answered
on May 29, 2022
Where can I get a set of brushes for a kango 950X
Unfortunately, you won't find them - Kango was a great hammer, but the company has been gone for many years and there are no parts available.
I would find a local repair shop that may have a different brand brush that is the same or bigger dimensions - by using a piece of 220 grit sandpaper on a hard, flat surface - you can sand them down to the proper size.
It will get you out of a bind
3/3/2021 2:37:44 PM •
Hammering
•
Answered
on Mar 03, 2021
Which type of oil for rok demolition hammer thank you
If an oil sight glass is in the modelrange of the brand ROK Rottela 40 , but if no sight glass is used in the model then often is to use special Grease lubrication. or only an special volume of oil and most used of them are zinc-free hydraulic based and included in the manual instructions of a maintenance set (service kit)wear parts set.
5/29/2019 9:53:04 AM •
Hammering
•
Answered
on May 29, 2019
Not finding what you are looking for?
