Belkin N - Recent Questions, Troubleshooting & Support


press red reset button in back for 2 minutes.

Belkin N600 DB... | Answered on Jul 16, 2019


You should check the connection between your router and modem. make sure your modem is properly connected from internet port of the router to the modem. for more information you may visit at how to troubleshoot belkin router blinking orange Fix Belkin Router

Belkin N150... | Answered on Sep 18, 2018


That's been a problem for years. Sleep mode turns off USB devices, and they seldom wake when the computer is activated again. To make sure this isn't the problem, you can
  • Go into Device Manager and under each USB Device, Power tab, disable "Let this device turn off to save power".
  • Edit Sleep Mode to not control USB devices.
  • Don't use Sleep Mode.
  • Unplug the adapter, wait a few seconds, plug in the adapter.
If none of these help, try a self-powered hub. The internal power supply lets you use about 500ma for each USB device, but some draw more current than that. The self-powered hub can deliver what's actually needed for the devices.

Belkin N600 DB... | Answered on Feb 18, 2018


You are changing the ssid so if you are using wireless you will lose the wi fi connection and would need to disconnect wi fi and then search wi fi networks for the new ssid and then connect to it.
you could connect by ethernet cable till you get it right .

Belkin N600 DB... | Answered on Nov 07, 2017


Start by checking for "link" between the modem and wireless router. This is usually a tiny light built into the network port itself on each piece of network equipment. It should be solidly on if the link is good. If it isn't on, check that you have the network cables plugged in good and that the cables or connectors are not broken or damaged. If you have another network cable, try it instead of the one you were using.

If these steps don't help, you can try fully resetting your wireless router to factory defaults, then reconfiguring it again. Consult the manual for your brand and model of wireless router for this. It may also have additional troubleshooting steps.

There is a chance your wireless router has simply gone bad. I've seen new Belkin wireless routers for as little as $29, so you may want to go that route, rather than spending too much time trying to troubleshoot the one you have.

Belkin Pre-N... | Answered on May 19, 2017


Range (distance from modem/router to computer) is shorter on higher speeds -- N signals won't travel as far through your home as G. Walls greatly reduce range. Move the computer closer to the modem/router and see if you don't get higher speeds. Then you can decide if you need to relocate the modem/router closer to the computer. The question is, why is Wi-Fi speed important to you? Your G speed is already 10x - 20x your Internet speed. Wi-Fi speed only matters if you're doing a lot of file transfers between devices inside your network. You may be trying to solve a problem you don't have.

Belkin N... | Answered on Apr 22, 2017


Put all your settings back to the way they were and check the time and date on your computer (also on the router), WPA uses encryption, if the time difference between the two is too great it can break the encryption (seen this often).

Belkin N150... | Answered on Mar 10, 2017


try to check if the ip of modem is the same as of router , if so change router , example : if both work on 192.168.1.1 than change router to 192,168.3.1 this might solve the problem , it did for me .

Belkin Pre-N... | Answered on Jan 18, 2017


Belkin USA Site

The above link has the drivers and instructions.
I would recommend you uninstall the drivers before installing, just to be sure.

Belkin N600 DB... | Answered on Nov 02, 2015


http://www.belkin.com/us/support-article?articleNum=4935

Belkin N... | Answered on Mar 14, 2015


Sounds like the driver is misbehaving. Try downloading the latest driver from Belkin and reinstalling.

Belkin N1... | Answered on Mar 02, 2015


Check the Advanced tab of the N300's Firewall settings to see if VPN passthrough is enabled. If it's not, the firewall will cut off VPN communications.

You may also need to run the VPN Wizard on the N300.

Here's the manual:
http://cache-www.belkin.com/support/dl/F9K1004v1%20manual%20-%20revA00.pdf

Belkin N300... | Answered on Mar 02, 2015


Hi
You should be able to do this from a web interface using an internet browser, or from the software utility that came with the unit and needs to be installed on your PC from the CD-ROM. Both thes methods should work on Win8.1 as you are altering the router settings not the PC settings. I give below a link to the router manual which will take you through both procedures.
http://cache-www.belkin.com/support/dl/MAN_F9K1102_8820-00777_RevA02_N600.pdf
I think pages 6, 20, 21 will be most relevant to you.
Cheers

Belkin N600 DB... | Answered on Nov 07, 2014

Not finding what you are looking for?

-3,966 questions posted

Ask a Question

Usually answered in minutes!

Top Belkin Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Belkin Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Belkin Computers & Internet

  • Forum

View Most Popular

  • Belkin Computers & Internet
Loading...