AT&T Lands Phones - Recent Questions, Troubleshooting & Support


In this article, you will meet a very good recovery program that will handle all the stress for you. It won't require a technician after all. You can do the job easier and faster.
For better step by step procedures follow these guides:
Step1. Download FoneDog - Android Data Recovery, Install and Launch
Step2. Connect Samsung Galaxy S Note to the computer
Step3. Select Files for Data Extraction
Step4. Select Device Fault Type
Step5. Download Mode
Step6. Retrieve deleted messages by preview and selection
Hope it can help you sooner. Good luck.

AT&T SL82218... | Answered on May 20, 2019


Do you hear tones when you press the buttons to dial?Many phones have the option to dial by pulses instead of tones. Make sure your phone is set to tones.

AT&T Lands... | Answered on May 13, 2019


REREAD THE INSTRUCTION MANUAL . IT TOOK ME SEVERAL TRIES TO DO MINE . 40 YEARS AGO

AT&T Lands... | Answered on Mar 26, 2019


If you need the remote access code for the answering system, then the original (default) access code is given in the manual on page 50 (page 53 of the PDF) and on 55 (page 58 of the PDF). See the manual online at https://att.vtp-media.com/ecp/documents/product_Product/364/UserManual/5977/SL82118_manual_i10.pdf . Unfortunately, if the remote access code has been changed, the default code will not work. As far as I know there is no way to reset the SL82318 remote access code to the factory default remotely. See page 50 of the manual to reset the phone's access code when you are using the handset. When you use the handset and start to change the code, the current remote access code will be announced first.

Any voice mail system would be accessed using the phone number and codes from your telephone service provider. This information will not correspond to the answering system of the SL82318.

I hope this helps.

Cindy Wells

AT&T Lands... | Answered on Mar 16, 2019


Phones show "in use" when the line voltage is low because another set is off-hook, which also happens when the line is unplugged. In other words, that is normal.

What happens when you do plug in the line? If it still shows in use then, the jack might be wired with reversed polarity. Try it elsewhere - someone else's house/office where the phones work "normally" to see what it does.

AT&T ATT... | Answered on Mar 09, 2019


Reverse the polarity of the phone wires.

-Some phones are sensitive to this; others do not seem to mind.

I believe you should reverse the red and green.

AT&T Lands... | Answered on Feb 03, 2019


This happened to me today!
Do the following in order:

1.take battery out of back of phone
2. unplug all phone lines from phone, then unplug all phone lines from wall
3. unplug ac from phone, then from wall
Wait 30 seconds.
In this order:
1. replace battery
2. replace phone line(s) to phone, then to wall
3. replace ac to phone, then to wall.

These steps solved it for me! Good luck.

AT&T 944 Four... | Answered on Jan 06, 2019


Having the exact same problem. Did you ever get it solved?

AT&T 944 Four... | Answered on Jan 06, 2019


Check your ground wire where the phone line comes into the junction box outside your house. It is either loose or corroded. It should be clean and clamped to a ground stake or water pipe like for an outdoor hose faucet. Check both ends of the wire. Without it, the phone system's impedance is so high that it will receive the 60 Hz hum from any electrical appliances around the house that are within a few feet of a line on an extension phone, answering machine or even an extension phone outlet wire running through a wall. These make great receiving antennas. good luck.

AT&T Lands... | Answered on Jan 04, 2019


That is not possible. Deleted means gone for good.

AT&T Lands... | Answered on Dec 31, 2018


If you delete the greeting you recorded, it should default to the canned response.

AT&T Lands... | Answered on Dec 05, 2018


Try unplugging your corded base unit, then replug. It should reset. Then you'll be able to go in and delete those messages.

AT&T EP5962... | Answered on Nov 03, 2018


You didn't iinclude the model number, so here is a link to AT&T manuals. If you like send a comment with the model number and I wiil try to help more.

http://telephones.att.com/att/index.cfm/customer-support/manuals/#40000

AT&T DECT 6.0... | Answered on Oct 30, 2018


Take the back cover off your phone and remove the battery. You will find the IMEI on the label there.
25592966-obkoyhm2j4njygclebv1o4cu-2-2.png

AT&T Lands... | Answered on Oct 30, 2018


Have you called customer service 1 (800) 222-3111, I'm sure this is an ongoing issue they can guide you through it.

AT&T E5921 5.8... | Answered on Oct 09, 2018


Google (AT&T)(1830)(manual) without parens for instructions.

AT&T Lands... | Answered on Sep 25, 2018

Not finding what you are looking for?
AT&T Logo

2,210 questions posted

Ask a Question

Usually answered in minutes!

Top AT&T Lands Phones Experts

Cindy Wells

Level 3 Expert

5870 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Marvin
Marvin

Level 3 Expert

84625 Answers

Are you an AT&T Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...