How do we get it unlocked

Unfortunately, the GLI.Pro BD 1600 turntable is a discontinued model and finding a manual for it may be difficult. However, there are a few places you can look for the manual:

1. Manufacturer's website: Check the manufacturer's website to see if they have an archive of older manuals available for download.
2. Online retailers: Some online retailers may have the manual for the GLI.Pro BD 1600 turntable listed on their website.
3. Second-hand marketplaces: The manual for the GLI.Pro BD 1600 turntable may be available for purchase on second-hand marketplaces such as eBay or Amazon.
4. User forums: Try searching for user forums or discussion groups related to the GLI.Pro BD 1600 turntable to see if any members have a manual they could share with you.

I hope this helps, and good luck finding the manual for your turntable!

I did this myself ,recently ,as far as I remember you select the service info readout with the button on the right hand stalk then hold it in for a few seconds until it resets (a little later I actually did the oil change )

Hi, if your not plugged into your amp via a dedicated phiono input, Ie CD or Aux then you need a preamp to boost the line levels. Cheers john. Styluscity

Helo
Assumes that you have its orginal remote control handset with your now, and posts this solution to your Lock Probelm. If you haven't it now with you, just try to buy a new one, or borrow it from any of your friends or relatives, who own the same model of TV, just for ulock it. After unlock, you can use any other universal remote control to control your TV.
Sinotec:
If you have the original remote (RC-A07) for Sinotec tv, then press and hold down the Music button for about 10 seconds. The tV will be unlocked. After unlock, you have ot set a new password. OK.

Normally this is the battery... Try the battery before considering to send the watch to Casio for service. Or, if you send it they will fix it and send it back. They are not very expensive for their service.

the instructions say they are the same for up to 06. Need a working remote to make this work. On your programmed remote:
- Switch the ignition to the on position.
- Press and hold the Unlock button for at least four seconds. While holding this button, press the panic button and then release both buttons at the same time. You may or may not hear a chime from the vehicle.
- Within 30 seconds, on all remotes to be programmed (including the original "programmed remote")press and release the lock and unlock buttons at the same time, followed by pressing ANY button on the remote.
- Switch the ignition to off or wait 30 seconds for the programming mode to clear.

Just did it last eve; also can find more details in the Owners Manual (However you only need one working keyless remote to program another keyless remote. You should be able to use the electronic vehicle information center (EVIC) on the overhead console to train remote (Owner's Manual, p. 132-133). However, on my 2005 Liberty this does not show up as an option like it does on my 2003 Liberty.) or Jeep KJ Service Manual.

Hope it works for you (remember rated this help).

To start the vehicle, press and release the Key/Trunk button two times within 2 seconds.

you have to resynch your remote once it looses power. the procedure is in your owner's manual. It can also be done from a scan tool but you would have to take the car to a shop. I beleive you hold the lock button and press the unlock button 5 times within 10 seconds and then put the key in the ignition but I cannot remember year for year procedures

Does the second remote work?  Have you changed the battery and then done any reset required by the manual?  Ten year old batteries are probably shot.

The home page for Cosley =

"http://www.crosleyradio.com/prods/cr78.html"

Contact and support links are near the bottom of the page (RHS)

Contact them and ask them if they have a user manual in PDF

format for download.

Martin
Please rate my answers.