Question about Haier Dishwashers

1 Answer

When i turn on dishwasher.. it beeps 3 times.. It does not respone to buttons except power button

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 78 Answers

Does your manual have a trouble shooting guide? 3 beeps is a code but im unsure for what.

Posted on Sep 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Top drawer on F&P dish drawer stuck on cycle & continuously beeping


You could isolate the top drawer by taking the controller power cable out. DIsconnect mains power to dishwasher, open top drawer and remove front cover carefull after removing 2 plastic pins on each side with plier. Controller box is on left top side, remove bottom connector and cover with insulation tape. Put things back and turn power back on.

But if you want to find the fault with top drawer then that is very trick if there is no fault code on panel except beeping First clean the top panel inside door with a clean damp cloth. If this does not change the situation, then it is very likely the controller is detecting some faulty sensor - and will need to find one by one. Are you ready for it?

Dec 17, 2012 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

I have a ge profile dishwasher model pdw9280j00ss. After a storm event, house lost power. Since that time, dishwasher constantly beeps; however has no power to it. shut off circuit, beeping stops; but...


http://www.geappliances.com/search/fast/infobase/10000380.htm

According to this link, it should reset after the power is shut off for awhile. Maybe try holding the start/reset button too. Also check the circuit breaker or any fuses

Aug 28, 2011 | GE 24 in. Profile PDW9880JSS Built-in...

1 Answer

Flashing start button, beeps, no other button functions


does it flash say 8 times then a little break then flash again 8 times or 9 or 10 . The flashes are giving the type of fault you have. Say 3 flashes then a tiny break then 3 flashes and a tiny break so on...

Mar 20, 2010 | Whirlpool Dishwashers

1 Answer

Dishwasher buzzer will not turn off. no lights on display, buttons have no effect, and killing power to dishwasher does not reset board.


You may be able to cancel the cycle buzzer by pressing the HEATED DRY button 5 times in 3 seconds. You should hear a 3 beep signal. If not your control board will have to be replaced.

Jul 16, 2009 | GE Dishwashers

1 Answer

My oven is beeping!


F1 Circuit board defective Replace control board
Good Luck and Please Rate Fixya!

Jan 07, 2009 | Electrolux Frigidaire Professional Series...

3 Answers

That Darn Beeping...


sorry I don't think ya can on most d/w's, fisher paykal you can....

Aug 14, 2008 | Bosch 24 in. SHY56A05 Stainless Steel...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Chen Dorot
Chen Dorot

Level 2 Expert

132 Answers

Tim Doolittle
Tim Doolittle

Level 2 Expert

102 Answers

Are you a Haier Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...