Question about Smeg DWI614 Built-in Dishwasher

1 Answer

Smeg di612ca (e2 error msg)

I have recently started having problems with the dishwasher beeping then stopping about 5 mins into its cycle , The error msg in the manual of the trouble shooting section suggest's that the error code is E2 .
I have turned it off and reset it a dozen times but the same problem keeps occuring.

Posted by on

  • Anonymous Nov 09, 2008

    I have a Smeg DI 612 CA Dishwasher. It fails to complete any cycles and displays an E2 fault. This is described as the system that limits the water has tripped. The dishwasher apppears to fill and drain and the float switch on the base panel has not tripped. I have tried to reset the dishwasher but to no avail. Beginning to suspect the printed circuit board is faulty.

×

1 Answer

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Smeg D1 612 CA dishwasher wont run


You may have to give a little more information.
Have a look at the manual, here -
http://www.manualslib.com/manual/343502/Smeg-Di612ca.html
and check for error codes/lights etc (p17; faults E1-E9)
Hope this helps

Oct 28, 2013 | Smeg Dishwashers

1 Answer

Fisher and paykel nautilus dishwasher


Does it fill with water? I would guess a fill/ drain/ heating problem. See if you can eliminate any of those.

Apr 12, 2013 | Fisher and Paykel Dishwashers

1 Answer

Smeg DW167.1 error code


I HAVE A SMEG DW167.1 AND IT COMES UP WITH A E9 FAULT, DOES ANYONE KNOW WHAT I CAN DO TO SOLVE THE PROBLEM ,THANKS

Jun 22, 2012 | Smeg Dishwashers

1 Answer

913T Dishwasher Stops after 10 seconds


913T is a very old model (1996), I have one, I'm not a repairer, I have the same fault. It doesn't have drawers or infrared or a display.
I've just shortened the ribbon cable, which had pinch damage at the door close pinch point. I used a male & female ribbon squeeze connector pair to make a good clean joint. With the cable fault it wasn't even starting the drain cycle. Now it does start, but then long beeps, and I suspect it's detecting a fault with the motor or a sensor or faulty wire, and is halting.
I've found running the rinse cycle first then allows the main wash cycle to run, no longer stopping at 10 seconds (after the initial drain), just as the first power wash commences.

May 24, 2012 | Dishwashers

2 Answers

LG DISHWASHER LEAKING WITH E1 ERROR CODE.


Hi phtanner,

The E1 error can be fixed by following my Tip below:

L.G DISHWASHER E1 ERROR...

Follow these directions, and the problem will be fixed.

Kind Regards :-)

* If this solution helped you, please rate it.

Jul 28, 2011 | LG 24 in. LDF 7811 Stainless Steel...

1 Answer

My smeg dishwasher stopped during a cycle and warning lights E2 come on. suggesting that it has drawn too much water and to contact customer technical services, any idea what i need to do


E2 shows that the water level switch has been tripped or its faulty,interupt the programm and switch off the dishwasher then switch it on ,programm it again and start the washing cycle again,if the problem persist then test the water level switch for possible replacement

Jan 10, 2010 | Smeg Dishwashers

1 Answer

My LG dishwasher stops running 5 mins in


The LE code means there is a problem with the washer motor. ( Motor error ) Condition : The motor is working abnormally. Possible cause : Wiring connections. The impeller of washing pump is locked. The rotor of washing motor is locked. The blade is locked.

Remedy: Correct wiring connections. Replace the cause of restriction. Replace the washing motor. Replace the PCB.

May 02, 2009 | LG Dishwashers

Not finding what you are looking for?
Smeg DWI614 Built-in Dishwasher Logo

1,930 people viewed this question

Ask a Question

Usually answered in minutes!

Top Smeg Dishwashers Experts

yadayada
yadayada

Level 3 Expert

67930 Answers

Cleverer2

Level 2 Expert

298 Answers

paul
paul

Level 3 Expert

757 Answers

Are you a Smeg Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...