Question about Samsung SpinPoint P80 SP0802N 80 GB Hard Drive

1 Answer

JUMPER SETTING I WANT TO CONNECT SP0802N HDD AS A SLAVE TO THE EXISTING HDD. PLZ HELP ME WITH THE SETTINGS

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 679 Answers

Hi,
to make a HDD as slave, put off the jumper out.

for any question ask me.
Thanks for your question.

Posted on Jan 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a jumper setting to run my hitachi 250 gb sata laptop hdd as a slave ?


There should be, look on the rear of the drive, close to the SATA and power connectors, you should see the jumper connections as well.

It varies from drive to drive, but the jumper setting could be engraved near the connector, look of SL for a slave setting.

If no, look on the label on the top of the drive, there should be the jumper settings listed there.
Some may be ambiguous, my last one offered the option of Master on / off. (Jumper in position 1 for on, no jumper for off) The off in this case was of course slave.

The result being, no jumpers - Slave.

Mar 26, 2011 | Hitachi 250GB Hitachi 2.5" SATA Hard Disk...

3 Answers

How can i make my Samsung sp0802 hard drive become the master instead of the slave... thank you very much


Hi Good day!!! follow this

1. Decide which hard drive will be the startup (master) drive. If this drive was the startup drive previously, or if it's a new hard drive, then the master drive designation will already be set.

2. To change the designation of a new drive to be a slave drive, skip to step 4.

3. To change the designation of an existing drive to be a slave drive: Turn off the computer, unplug the power cord, remove the drive from its drive bay, and disconnect the drive from its power cord and ribbon cable.

4. Check the hard drive documentation or the label on the drive itself for master/slave jumper settings.

5. Find the jumpers on the circuit board of the drive. Jumpers are plastic plugs with metal sleeves that form a circuit between a pair of pins. Jumper locations are labeled on the board with a J followed by a number (such as J20).

6. Use tweezers or very small pliers to remove or reposition the jumpers to the configuration shown in the documentation or on the disk label.

7. Install (or reinstall) the hard drive in the computer. (See "How to Install a Second Hard Drive.")

Don't forget to vote thanks!!!

Nov 02, 2010 | Samsung SpinPoint P80 SP0802N 80 GB Hard...

1 Answer

Jumper settings when used as a slave in a HP pavilion 6835


There are 3 pairs of pins:
* MA(ster)
* SL(ave)
* C(able)S(elect)

Move the jumper to connect the two 'SL' pins, if you want to use the drive as a "slave" drive.

Or, move the jumper to the 'CS' pins, and the drive will auto-configure itself.

Sep 21, 2010 | Samsung SpinPoint P80 SP0802N 80 GB Hard...

1 Answer

Jumper settings for a maxtor N256 master with slave


Select the maxtor HDD as master by setting the Jumper to the extreme left of the hdd; i.e. next to the data cable.
Remove all jumpers from the other HDD which you want to put as slave.

Sep 02, 2009 | Maxtor DiamondMax 80 (96147H6) 61.4 GB...

1 Answer

Jumper settings


the junper setting on a hard drive are:  
Master - if this is the only hard drive in the computer, with the operating system on it.
Slave - If the hard drive is used with another hard drive in the computer.
The instructions are printed on the hard drive. 

Apr 04, 2009 | Samsung SpinPoint P80 SP0802N 80 GB Hard...

2 Answers

Samsung SP0802N 80GB Slave


Go into the control panel. Press administrative tools. Select computer management. Under storage select disk management. Look for the hard drive. Make sure there isn't an additional partition on the drive. If there is you can change and delete partitions on this drive as well.

Jan 03, 2009 | Samsung SpinPoint P80 SP0802N 80 GB Hard...

3 Answers

Which jumper is slave on my disc drive?


Greetings my friend...Put it to cable select mode(CS) so that the cable will automatically set your existing HDD as master and the new one as slave!
Good luck!

Oct 19, 2007 | Hard Drives

Not finding what you are looking for?
Samsung SpinPoint P80 SP0802N 80 GB Hard Drive Logo

Related Topics:

926 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Hard Drives Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Abhinandan  Patil
Abhinandan Patil

Level 3 Expert

562 Answers

Terry Allen
Terry Allen

Level 3 Expert

680 Answers

Are you a Samsung Hard Drive Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...