Question about Pioneer Audio & Video Receivers

1 Answer

Jonny Rafael Every time i turn on my amp it stops and says Amp Err and shuts down and wont let me turn on like in about 20 min.I dont know wats wrong but i need help please.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Says amp error on the amp? what kind of amp? Have you checked the fuses and are you properly installed ie. remote wire to a remote power source. Properly grounded? Power wire to a constant power source? Please be more specific?

Posted on Aug 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

After turned on the power, the unit shuts down immidietly


There is a problem in either the power supply or amplifier output stages. The unit is programmed to shut down in such an event to protect other circuitry.

Using a schematic see if you can isolate the power going to the output stages. If unit stays on then the anomaly is in power amp stages. If it still shuts off problemo is in power supply - check diodes and capacitors.

Mar 12, 2015 | Onkyo Ht-r510 5.1 Channel 100 Watt Av...

1 Answer

App err


PDF]VSX-D414 VSX-D514 - Pioneer

www.pioneer-latin.com/downloads/xre3077a.pdf
Increase the separation between the equipment and receiver. - Connect the .....AUDIO/VIDEO MULTI-CHANNEL RECEIVER VSX-D514. RCE. VSB. MODE.

Pioneer VSX-D514 Receiver Repair Questions,... - Fixya

www.fixya.com > Forum > Audio & Video Receivers > Pioneer
Recent Pioneer VSX-D514 Receiver questions, problems & answers. Free expert DIY tips, support, troubleshooting help & repair advice for all Audio & Video ...

app err Turns on then says amp err. - Fixya


Jan 26, 2012 | Pioneer VSX-D514 Receiver

1 Answer

My JVC SP NX-D7 was accidentally locked. And a cd was stocked in it. How can i unlock it so that i can get it?


turn on device ..........press the stop & eject button at the same time..... if this do not work unplugged for 15-20 min and repeat the process

Apr 17, 2011 | JVC Audio & Video Receivers

1 Answer

The power does not turn on no matter what outlet I plug it into. When I first turned it on Amp Err plashed on the screen and it clicked and shut off.


The amplifier shuts down as a protection to prevent further damage.
Most of the times it means one of the power amplifiers has malfunctioned and is causing a short.

If you have nothing connected to the speaker terminals when it's doing this you should have it repaired.
if you do have speakers connected try disconnecting them.

Dec 21, 2010 | Pioneer VSX-52TX Receiver

1 Answer

Hello, I just hooked up our new PS3 Game system to our Denon 2803. Was happily playing it when it cut out on me after about 30 mins of playing. Turned the volume down to see if I was overloadingit but it...


looks like you are overheating it let it cool down for at least 20 min. and then when you use it just lower the volume, after that it should give you no more troble

Dec 18, 2009 | Denon AVR-2803 Receiver

2 Answers

Amp err


Same problem here VSX-916 AMP ERR

Jan 28, 2009 | Pioneer VSX-D912 Receiver

1 Answer

Vsx-d412 displays "amp err" then


This is the same as "protect" mode. Basically the unit has detected a problem with the output stage of the amplifier and has shut down to prevent further damage. Usually this is caused by defective output transistors. Expect a parts cost in the range of $15-$40. Add in the local labor rate for the total repair bill.
Dan

Apr 15, 2008 | Audio & Video Receivers

1 Answer

Onkyo TX-SR805


When you turn up the volume, the amp works harder and generates more heat. There is a small transistor attached to the heat sink that detects the excessive heat and shuts down the amp before there is damage. There is a circuit inside that should detect the increased volume and turn on the fans. Either this detection circuit is defective or the fan driver transistor is defective. This unit may need to see a servicer. In the meantime, you can provide additional air flow to keep the heatsinks working efficiently. Realize that this is a short term "fix" and you should really get this repaired ASAP to prevent permanent damage to the amp components.
Dan

Mar 23, 2008 | Audio & Video Receivers

3 Answers

Stand by button flashes but receiver wont turn on


I have vsx-d812 that has an AMP ERR in error menu. the troubleshooting was found to be Q696 and Q697 in the DC prot. area on "C" board, up near front toward diplay in center of c board. You can get access to error codes on VSX pioneer unit by pressing "enter" and "adv. surr." simultaneously for 2 sec. The display should show what error code you are experiencing. I believe there are three diff. error codes. 1) AMP ERR 2) OVERLOAD 3) BOAD ERR (not mistyped) I hope this helps pinpoint error code for ya.

Oct 07, 2007 | Pioneer VSX-816-K/S Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio & Video Receivers Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Pioneer Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...