Question about Jabra BT160 Wireless Headset

1 Answer

My LED never goes solid...??

I bought a brand new BT160 online and when I got it, I opened it and plugged it into the charger and the LED flashed blue, but did not stay solid. I left it on the charger for like 3 hours, just in case. I then tried to turn it on and set it to pairing mode, but still no solid LED.

Any thoughts?

Posted by on

  • Anonymous Feb 07, 2009

    same problem here it just keeps blinking with a blue light

  • Anonymous Mar 21, 2009

    I have the same exact problem. The light will just flash when I plug it in. And I let it stay plugged in all night. Still never turns on.



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer


Posted on Mar 20, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I can not get the headset to turn on.

If I read everything correctly in the manual I believe the light only stays on when the device is in the pairing mode. If the light flashes every second, the headset is on a call, if the light flashed every three seconds, it is in standby mode.
Standby mode: is when the Jabra BT160 is passively waiting for a call. When you 'end' a call on your mobile phone, the headset goes into standby mode.

Make sure your phone is bluetooth equipped.

You must first successfully pair the headset with your phone. The manual shows you how.....
1. Put the headset in pairing mode Make sure that the headset is on. Press the answer/end button and press the volume up (+) button at the same time, until a solid blue light comes on.
2. Set your Bluetooth phone to 'discover' the Jabra BT160 Follow your phone's instruction guide. This usually involves going to a 'setup,' 'connect' or 'Bluetooth' menu on your phone and selecting the option to 'discover' or 'add' a Bluetooth device.
3. Your phone will find the Jabra BT160 Your phone then asks if you want to pair with it. Accept by pressing 'Yes' or 'OK' on the phone and confirm with the passkey or PIN3 = 0000 (4 zeros). Your phone will confirm when pairing is complete. In case of unsuccessful pairing, repeat steps 1 to 3.

Go here for a copy of the owners manual....

Hope this helps.....

Jan 27, 2018 | Jabra BT160 Wireless Headset

3 Answers

Air hogs pocket copter, brand new. Inserted brand new batteries into charger and controller per instructions. Plug the helicopter into charger and led blinks red as stated. About two or three minutes into...

You bought a defective mini copter, the internal micro relay is malfunctioning and I hope you could bring it back where you bought it. Replace it with a new one and let them try to test flight it before you go home.

Hope that helps you out.
Thanks for asking FixYa!

Aug 09, 2011 | Toys

2 Answers

Flashing LED on Samsung SBC-N1 Charger

LED flashing is unable to charge

Sep 05, 2009 | Samsung Cameras

1 Answer

Just quit

Bad STKs 392-110s 2) also two 3.9 ohms resistor are open replace STKs with 180s.

Aug 27, 2008 | Televison & Video

10 Answers

Battery Charger Olympus li-40c

I had this problem a few weeks ago (i.e. flashing red LED). All I did was remove the power plug from the charging unit, turned it around 180 degrees, then plugged it back into the charging unit. Red LED came on steady & the battery (which is the one that came with the camera) recharged as normal.

Aug 25, 2008 | Cameras

3 Answers


sounds like a dead battery. Plug the origional charger into it and the front led (below the flash) should flash red. If the red led in the back of the camera flashes or stays lit, then you have the wrong charger plugged in. (the camera won't power up if the back red/green led is on when plugged in)

May 08, 2008 | Jazz DV-179 Digital Camera

2 Answers

CHARGING My Jabra bt160

I think something's goofy with these headsets. I bought 2 of them recently (one for me and one for my g/f). Within a week or so, she told me hers just "died" - and she couldn't get the blue light to come on when it was plugged into the charger.

Mine acted dead too, just a day or so before she told me about her problem. On mine, I think I just held down the "volume down" button and the main button at the same time for about 15 seconds and it appeared to "reset" it. That apparently didn't work for hers, but oddly enough - after a few days, we plugged it into my charger and it started working again!

Dec 09, 2007 | Jabra BT160 Wireless Headset

2 Answers

Jabra bt160

hold the button down for a long time

Apr 17, 2007 | Jabra COMMUNICATIONS BT160 Bluetooth...

Not finding what you are looking for?
Jabra BT160 Wireless Headset Logo

Related Topics:

574 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jabra Radio Communications Experts

TO Lady

Level 3 Expert

638 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

Michael Vincent Cruz

Level 3 Expert

868 Answers

Are you a Jabra Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides