Question about Invicta Dragon Lupah 2093 Wrist Watch

1 Answer

Invicta Lupah crown replacement?

I lost the crown that sets the time for my Lupah and have a new one, but have now idea how to install it properly. Any suggestions would be greatly appreciated.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 183 Answers

If there is no problem with the stem then you can just screw it on. I suggest using a thread lock to insure a good fit. Start by taking the back off and hold the stem in place with a pair of needle nose pliers. Be sure to start by turning the crown in the reverse direction so you dont cross thread. Once you feel it hit the beginning of the thread you can turn in the on direction.
I always recommend having this sort of service done by a watch maker/technician who can reseal the watch and pressure test it to be sure it is still water resistant.

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set the day of the week


here is your manual (I think)
http://cdn.invictawatch.com/invictawatch/website2014/webroot//uploads/manuals/2-8040n-pdf

If not, their site is pretty good.

http://invictawatch.com/service/view-the-instruction-manuals

nice video but as good as a chocolate teapot!

https://youtu.be/iv0aXQNH4yY


anyway, here is your info

Invicta Watch Setting Instructions By Ashley Brown eHow Contributor Found This Helpful A watch is only useful if it displays the correct time. Over time, your watch may display the incorrect time as the battery wears down. After installing a new battery, you will also need to reset the time. All Invicta watches have similar instructions for setting the time. Setting the time does not require any tools or equipment.

Other People Are Reading

Watches with Time Only
  1. Pull out the crown. The hour and minute hands will stop.
  2. Turn the crown until the hour and minute hands are positioned on the correct time.
  3. Push in the crown to start the watch.
Watches with Time and Date
  1. Pull out the crown to the first position. The crown can be pulled out to two different positions. Pull gently once to reach the first position.
  2. Turn the crown until it reaches the correct numerical date.
  3. Pull out the crown to the second position.
  4. Turn the crown until the hour and minute hands correspond to the correct time.
  5. Push in the crown twice. It should now be resting firmly against the watch, in its original position.
Watches with Time, Day and Date
  1. Pull out the crown to the first position.
  2. Turn the crown to reach the correct day.
  3. Turn the crown clockwise to reach the correct date.
  4. Pull out the crown again to the second position.
  5. Turn the crown until the hour and minute hands display the correct time.
  6. Push in the crown twice so it rests against the watch. The crown should be back in its original position.


Read more : http://www.ehow.com/how_7352591_invicta-watch-setting-instructions.html

Sep 13, 2015 | Invicta Watches

1 Answer

I am looking for a new watch band for my Invicta Pop Lupah 2397 (turquoise). Where can I order one ? Julie


Visit the Invicta site. Their posted price list has prices for what I would expect is replacing the original watch band .

http://www.invictawatch.com/invicta/price_list

If you do not have a local delaer whom you can visit to onbtain a new watch band information on how to ship your watch to Invicata can be found here:

http://www.invictawatch.com/invicta/shipping

Mar 30, 2011 | Invicta Lupah POP 2397 Wrist Watch

1 Answer

I have an original Invicta Men's Lupah w/ chronograph. Which of the 3 buttons on the side of the case is for setting the date? I can't seem to figure out how to set/reset the date. Thanks in advance...


If your lupah has a screwdown crown (middle button), you need to unscrew it. Pull out the middle button 1 click (it should have 2 clicks...if it's all the way pulled out, then you have gone too far) and turn the screw counter clockwise. Some model's you have to give them a couple good turns to adjust a single day, so don't give up if you move it a quarter turn and nothing moves. Once done adjusting, just push the crown back in and lock it down (lock down crown isn't a necessity. It is rather a means of keeping water at pressure from entering your time piece. So don't freak out if your model doesn't have a screwdown crown. Not all of them do). Best of luck to you!

Jun 14, 2010 | Invicta Dragon Lupah 2094 Wrist Watch

1 Answer

How do you set the watch


Go to http://www.invictawatch.com/new/product/search.php?CAT_REF_NBR=7&prn=2095#2095 (this should be part of the "collections".

Click on the tab maked "manual" and you should find the information you need.

May 25, 2010 | Invicta Lupah Dragon 2095 : Eta 1/60...

1 Answer

How do i set the time on an Invicta Lupah mens watch with three subdials


The Lupah has a chronograph so dont worry about the sub dials while your setting the time. Pull the crown out to the first position and set the time. For the date pull out to the second position and set the date.

To set the chronograph sweep arm pull the crown out and press and hold down the start button. The sweep arm will move into position. Stop it on the 12:00 or 0 position.

Jun 09, 2009 | Invicta Dragon Lupah 2093 Wrist Watch

1 Answer

I can't figure out how to adjust the offset chronograph


This is to adjust the seconds hand or minutes hand for the chronograph. Pull the crown out either one click or two ... depending on the models. Squeeze and hold the top and bottom buttons at the same time (timer stop and reset buttons). Hold down together for 2+ seconds. The chronograph hands should reset by spinning around and stopping at 0. If the don't stop right at zero, you can now adjust where they stop. Leave the crown where it is in that same position out. Press the top chronograph button and hold it down for fast movement or short presses for fine movement to adjust til it stops at the top. This will adjust where the seconds hand stops. Then click the bottom chrono button once. Repeat what you did with the top chrono button and it should allow you to fine tune the position for the next dial, and so on. When you are done, press the crown back in all the way to the normal position.

May 21, 2009 | Invicta Dragon Lupah 2093 Wrist Watch

1 Answer

How to set a invicta 3443 watch up


To set the time pull the crown out to the first position and set the time by turning the crown. Pull the crown out to the second position to set the date. Since this is a diver model you will need to unscrew the crown before it will pull out. Make sure you replace the crown and screw it back down for a good protective seal.

The alarm sets the same way. Unscrew the button to set.

Nov 24, 2008 | Invicta Pro Diver Collection Grand Diver...

1 Answer

Invicta Lupah #2094


The Lupah is a quartz movement so try having the battery replaced.

Dec 26, 2007 | Invicta Dragon Lupah 2094 Wrist Watch

Not finding what you are looking for?
Invicta Dragon Lupah 2093 Wrist Watch Logo

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Invicta Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Jimmy Accardi

Level 2 Expert

97 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you an Invicta Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...