I need repair manual for HP iPAQ 1940 pocket PC, I have a malfunction of the screen, it does'nt act on any tapping. But the 4 bottons on the front side of the cabinet is working OK ! I shall bee happy for any advice. Best Regards Lau Lausten [email protected] I have performed resetting by pressing the reset contact on the cabinet lower left side

To perform a hard reset you need to press buttons 1 and 4 in addition to the reset hole. This should do the trick.


The guidelines for resetting your phone is given below

Performing a Hard Reset

Perform a hard reset only when you want to clear all
user-installed settings, applications, and data from RAM
(Random Access Memory), where data and applications you have
loaded are stored.

CAUTION: If you perform a hard reset, your Pocket PC loses all data
and programs not saved in iPAQ File Store.

To perform a hard reset:

1. Press and hold down the Calendar and iTask buttons.
2. While holding down these buttons, use the stylus to
lightly press the Reset button on the bottom of the iPAQ
Pocket PC for about two seconds.

HP iPAQ hx2410 Hard reset

3. When the Pocket PC screen begins to fade, release the
Calendar and iTask buttons first, and then remove the stylus
from the Reset button.

Note: If you simultaneously push and hold the Reset, Calendar,
and iTask buttons for more than two seconds, the battery
disconnects. To restart the device, either plug the device into the
AC Adapter or press the Reset button again.
After performing a hard reset, you may need to reinstall
applications stored in iPAQ File Store to restore shortcuts and full
functionality.

4. The Pocket PC resets and powers on.

To return your iPAQ Pocket PC to factory settings after
performing a hard reset:

1. Tap Start > Programs > File Explorer > My Device.
2. Tap the iPAQ File Store folder to open it.
3. Tap Edit > Select All.
4. Tap and hold the selected files, then tap Delete.
5. Tap Yes to delete all file in iPAQ File Store.

1. urn on your HP iPAQ Pocket PC.
   
2. Use your stylus to tap on the "Start" menu.
   
3. Tap on the "System" tab.
   
4. Tap the "Screen" icon.
   
5. Tap the "Align Screen" button.
   
6. Tap the center of the cross-hair object carefully at each location as it moves around the screen.
   
7. Tap "OK" to complete the screen alignment.
   

Performing a Hard Reset

Perform a hard reset only when you want to clear all
user-installed settings, applications, and data from RAM
(Random Access Memory), where data and applications you have
loaded are stored.

CAUTION: If you perform a hard reset, your Pocket PC loses all data
and programs not saved in iPAQ File Store.

To perform a hard reset:

1. Press and hold down the Calendar and iTask buttons.
2. While holding down these buttons, use the stylus to
lightly press the Reset button on the bottom of the iPAQ
Pocket PC for about two seconds.
3. When the Pocket PC screen begins to fade, release the
Calendar and iTask buttons first, and then remove the stylus
from the Reset button.

Note: If you simultaneously push and hold the Reset, Calendar,
and iTask buttons for more than two seconds, the battery
disconnects. To restart the device, either plug the device into the
AC Adapter or press the Reset button again.
After performing a hard reset, you may need to reinstall
applications stored in iPAQ File Store to restore shortcuts and full
functionality.

4. The Pocket PC resets and powers on.

To return your iPAQ Pocket PC to factory settings after
performing a hard reset:

1. Tap Start > Programs > File Explorer > My Device.
2. Tap the iPAQ File Store folder to open it.
3. Tap Edit > Select All.
4. Tap and hold the selected files, then tap Delete.
5. Tap Yes to delete all file in iPAQ File Store.

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

1. Plug the charger adapter into the charging port on the bottom of the HP iPAQ Pocket PC.
   Figure : Charging the battery
2. When the power indicator on the top of the HP iPAQ Pocket PC turns solid amber, the unit is fully charged and can be disconnected from the AC adapter (approximate time to fully charge a unit is four hours).

NOTE: The amber charge light blinks while the battery is recharging and turns solid (nonblinking) when the battery is fully charged.In the event of a low backup battery warning, charge the unit immediately before removing the main battery to avoid data loss. To view the amount of charge left in the backup battery, tap Start, Settings, the System tab, and Power.
Charging with the universal desktop cradle and AC adapter Use the universal desktop cradle to charge the HP iPAQ Pocket PC, or synchronize the HP iPAQ Pocket PC with a computer.
Follow these steps to charge the HP iPAQ Pocket PC using the universal desktop cradle:

1. Plug the AC adapter into an electrical outlet and connect the other end of the AC adapter to the AC connector on the universal desktop cradle.
2. Connect the serial or USB cradle cable into the appropriate port on the desktop PC.Figure : Connecting with the cradle
3. Slide the bottom of the HP iPAQ Pocket PC into the cradle and push firmly to seat it.

CAUTION: To avoid damaging the HP iPAQ Pocket PC or the cradle, make sure the pins are aligned before pushing the HP Pocket PC into the cradle.

Figure : Charging with the universal desktop cradle

1. AC adapter into electrical outlet
2. AC adapter into universal desktop cradle
3. HP iPAQ Pocket PC into cradle

NOTE: The amber charge light blinks while the battery is recharging and turns solid (nonblinking) when the battery is fully charged.There are stabilizers located in the universal desktop cradle that assist in aligning the unit when there is no expansion pack attached. When placing the HP iPAQ Pocket PC with an expansion pack attached into the universal desktop cradle, the stabilizers will be pushed down by the expansion pack. To release the stabilizers for use without an expansion pack, press the button on the back of the cradle.
Charging with the optional USB Autosync cable Charge the HP iPAQ Pocket PC using the optional USB Autosync cable by connecting the Autosync cable to the HP Pocket PC and the personal computer. The HP Pocket PC will be charged using power from the personal computer.
For more information on charging the HP Pocket PC using the optional USB autosync cable, from the Today screen, tap Start, Settings, the Systemtab, Power, the USB Charging tab, Settings, and Help.
Charging a low battery The HP iPAQ Pocket PC will not turn on if the battery has a low charge (less than 3.2 Volts). Fully charge the battery prior to using the HP Pocket PC.
If the charge on the battery goes below the 3.2 Volts as a result of not being connected to the universal desktop cradle or the AC adapter, no damage will occur to the battery. However, the HP iPAQ Pocket PC charge indicator light will not flash until the battery reaches the minimum charge of 3.2 Volts and a normal reset is performed.
Follow these steps to charge and reset the HP iPAQ Pocket PC:

1. Connect the HP iPAQ Pocket PC to an A/C power supply.
2. Charge the battery to the minimum level of 3.2 Volts (this will take 5 to 30 minutes depending on the current charge level).
3. Perform a normal reset by using the stylus to lightly press the Reset button on the bottom of the HP iPAQ Pocket PC.
4. Turn on the HP iPAQ Pocket PC.

Keep the HP iPAQ Pocket PC connected to the universal desktop cradle or AC adapter when it is not in use.

plug in the charger - then press the soft reset button with the stylus - let sit for about a day or so...:)

Thank you! This is a really good page!

Mine hp ipaq also froze up, but I tapped the screen until they moved around all in alignment, and I got the basic things back (my programs, Media Player etc. but I can't sync it with my computer. It doesn't recognize the name of my handheld.

The factory-stock 1940, which uses Windows Mobile 2003, doesn't offer landscape mode.

You can get a 3rd party program called Nyditot Virtual Display that will let you use the 1940 in landscape mode, but I've used it before, and although it works, the problems it creates are not worth it. Besides, that program's not free.

Adobe offers a pdf reader for free that let's you read pdf files in landscape mode.

 connect the cable with pc , open the active sync on ipaq then connect the cable with ipaq..if not still soft reset ur Pocket PC and reconnect.