Question about Linksys Wireless-G WRT54G Router

2 Answers

Hey, i want connect with wireless router but i forget my password i want help with that thanks

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 45 Answers

You could always go into the router and setup the password again. If you have left the router with the default settings, then you would go into your browser and type 192.168.1.1 into the address bar and hit enter.

When presented with User Name and Password, Leave Username Blank, and use admin for Password, all lower case.

Then you can go to the wireless tab and change your security settings.

Good luck.

If you've changed the login Username and Password for the Router itself, you will have to do a Hard Reset. This will put all settings back to default, including the above user/password.

To Hard Reset, press and hold the reset button on the back of the router using a ballpoint pen or similar for at least 30 seconds, then let go. It will reboot, and you can log in using 192.168.1.1 and 'User' Left Blank 'Password' admin.

Posted on Aug 28, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Have you tried admin for the user name and admin as the password ?

Robert

Posted on Aug 28, 2008

2 Suggested Answers

  • 16 Answers

SOURCE: fogot password on this wireless router

What brand/model of wireless router are you using?
Most wireless routers have a "Reset" button on the side or under. You need to press this button for a couple of seconds while the unit is on (usually 10 - 30 seconds depending on the model). This will reset the router to factory default settings.
All the best!

Posted on Jan 30, 2009

  • 3 Answers

SOURCE: setting password to buffalo wireless G router!

Go into the router by typing 192.168.1.1
Username could be root or admin
There should be no password
Go into Advanced->Wireless Config->Security
Choose the type of Security you want to use
Choose a new password.

What you need to do may differ slightly from router to router but it is pretty much the same thing from router to router. Make sure you save the changes before you exit and record any passwords for future reference.

Posted on Aug 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find out my wep key password


Hi,

Welcome to Fixya. If you need your Wep Key (Passphrase) we can access the Wireless Settings Page of the router to obtain the information needed.

To access the router page you need a working computer that is connected to the router. To access your router you need to use a computer that is connected to it. Open a Browser then type 192.168.0.1 or http://routerlogin.net. The Default username is admin and the password is password. Password is case sensitive.

Go to the Wireless Tab select Wireless Security under the Security Mode you will see there Network Key (Wep Key) or Passphrase. The Network Key serves as a password or security code on your network to make it secure. Network Key is case sensitive.

Don't forget to say thanks. Thanks for using Fixya

Mar 29, 2011 | NetGear WGR614 Wireless Router

1 Answer

My daugher recently hooked up her router to my computer but she somehow has lost the disk and manual and does not know how to password protect my network. Any help would be appreciated Thanks Linda


hey,

Login to the routers home page (details under neath or behind the router). Once you login, go to wireless--> settings or wireless security page and then choose WPA2 or WPA PSK and enter the password and save the changes. After save, you will need to re-establish the connection to your laptop and you will be prompted for a password on the computer.

Cheers!!!

Feb 16, 2011 | D-Link RangeBooster G WBR-2310 Wireless...

1 Answer

I am trying to connect my Ipad to my wireless router (Wi Fi) and the Ipad is telling me I have enter the incorrect password.. I know that I am entering the correct password.. Please help me.


Hi,

Welcome to Fixya. If you iPad is not accepting you password you can check the password or Network Key on your router. To access the router page you need a working computer that is connected to the router. To access your router you need to use a computer that is connected to it. Open a Browser then type 192.168.0.1 or http://routerlogin.net. The Default username is admin and the password is password. Password is case sensitive.

Go to the Wireless Tab select Wireless Security under the Security Mode you will see there Network Key or Passphrase. The Network Key serves as a password or security code on your network to make it secure. Network Key is case sensitive.

Don't forget to say thanks. Thanks for using Fixya

Feb 07, 2011 | NetGear WNR1000 Router

1 Answer

I am trying to set up NetFlix on my Wii --- I need the default info for my NetGear wireless router????


Hi,

Welcome to Fixya. Im not quite sure what password you're reffering to if ti's the rotuer password or the Network Password or Network Key. Listd below are the steps on how to obtain the Network Password and the Router Password.


To access your router you need to use a computer that is connected to it. Open a Browser then type192.168.0.1 or http://routerlogin.net. The Default username is admin and the password is password. Password is case sensitive. Go to the Wireless Settings Page of your router. Look for the SSID or the Network Name and the Network Key or Passphrase. You can personalize it so that you can easily remeber the details. Make sure you connect to your SSID and enter the Network Key to make it secure.

If you think this is helpful rate me and dont forget to say thanks. Thanks for using Fixya.

Feb 06, 2011 | NetGear WGR614 Wireless Router

1 Answer

Trying to connect my wii to the internet ,need a password


Hi streborm,

Welcome to Fixya. Im not quite sure what password you're reffering to if ti's the rotuer password or the Network Password or Network Key. Listd below are the steps on how to obtain the Network Password and the Router Password.


To access your router you need to use a computer that is connected to it. Open a Browser then type192.168.0.1 or http://routerlogin.net. The Default username is admin and the password is password. Password is case sensitive. Go to the Wireless Settings Page of your router. Look for the SSID or the Network Name and the Network Key or Passphrase. You can personalize it so that you can easily remeber the details. Make sure you connect to your SSID and enter the Network Key to make it secure.

If you think this is helpful rate me and dont forget to say thanks. Thanks for using Fixya.

Feb 06, 2011 | NetGear WGR614 Wireless Router

1 Answer

How do i get a secure connection through my router


Hi,

If you want to setup a password or security on your router you need to access the Wireless Settings Page. To access the router page you need a working computer that is connected to the router. To access the router page just open a browser then type 192.168.1.1, the Default username is blank and the password is admin. Go to the Wireless Tab select Wireless Security on the Dropdown next to Security Mode select either WEP or WPA. Then Personalize your Network Key. The Network Key serves as a password on your network to make it secure. Then Save the settings

If this works dont forget to say thanks. Thanks for using Fixya.

Feb 05, 2011 | Linksys Wireless-G WRT54G Router

1 Answer

Is there a eay to password protect the Belkin Play Router so shen you get ready to use it you have to put in a password and keep unauthorized users off you network?


wau amigo creo que estamos hablando en Espanol ..

Ok si es asi seria mejor para mi hey hey.

ok lets solution your problem

ok change security mode is easy in router belkin
just ping 192.168.2.1 open setup page and get inside your router

click in Security and change the password for any you like apply changes and ready you have a new password .

other choice disable SSID share, so dont body will be see your Wireless SSID.
any question ask me for a remote you PC

Cualquier pregunta solo escriveme y te ayudare amigo

Don't forget to rating this .. thanks

Sep 11, 2010 | Belkin Wireless Play Router (F7D4302)

1 Answer

Hey i have a problem i whant to put my wireless router on code/password so can u help me and explane me how to do that?


You can secure your wireless network wit WEP or WAP code.
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
For belkin router http://192.168.15.1
or
http://192.168.2.1

If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Click on wireless settings then enable WEP Security then add WEP code .It is your password to connect wi fi.Then save settings and restart router.
Then you can connect your wi fi network with that code.
Thanks for using FixYa.

Jun 29, 2010 | MSI RG54G2 Router (MS-6848-002)

1 Answer

Hey. How can I connect to the linksys router in order to change the settings? There's some address I can put into my safari that will take me there, right?


default IP of router is 192.168.1.1
then it will open the page
the default user name and password is
admin

if you are unable to open this page through wireles, then try connecting the router to pc through lan wire.

dont forget to vote

Nov 19, 2009 | Linksys Wireless-G WRT54G Router

6 Answers

Connecting my westell 6100 modem to my router


i there ;
the solution for ur problem is :
> As ur isp is verizon so they must have provided wu wuth a username and password ...
> Open the routers page 192.168.1.1 ...
> Instead of automatic configration click on pppoe ...
> type in username and password for more help contact technical support at 1866-283-6613 . i hope this will help Linksys Tech support

Dec 09, 2007 | Linksys Wireless-G WRT54G Router

Not finding what you are looking for?
Linksys Wireless-G WRT54G Router Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18297 Answers

Mike

Level 3 Expert

4331 Answers

Steve

Level 3 Expert

3287 Answers

Are you a Linksys Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...