Question about Bosch Nexxt 300 Series WFMC2201UC

4 Answers

Error code E:13

During the rince cycle the softner no longer is added and, after filling with water, the washer stopd with the error code E:13 on the display. Any insight?

Posted by on

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Bosch Master
  • 19,396 Answers

I thin E13 is motor error, I will check.

Posted on Sep 03, 2008

  • Ginko
    Ginko Sep 03, 2008



    E-13 error code means 'drain timeout code'.

    This happens when the pump run a
    certian amount of time and cannot do fully draining.
    This can be commonly coused by a clogged drainline
    , a clogged pump, a faulty pump, or pump not receiving power.
    In most occasions you find something jammed
    in the pump, or the pump has blown.
    You access the pump removing the panel at the back of the washing
    machine at the base of machine. Once you get to the pump you unplug the
    two hose, remove the pump unplugging wires, and lifting the plastic
    block. Then you clean or replace the pump.



×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 521 Answers

E13 code means Pressure switch Fault

To check :- Remove Plug First ( Remember Safety First )
The pressure switch is at the top, its move likely to be a blocked pressure bottle, which is under neath the tub accessed via the rear bottom access panel 3 to 4 screws. the bottle is on the side of the filter with a small clear tube going up to the pressure switch. Clean this bottle out.

pls do rate the solution

thanks.
regards.
fixya expert team

Posted on Sep 03, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

Hi,

Cause: Latch Problem Example: Latch does not run Corrective Action: Check for voltage to latch motor

Posted on Sep 03, 2008

  • Priya darshan Sep 03, 2008

    Please don't forget to accept the solution as fixya.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,142 Answers

E13 Water leak in tub or air leak in air bell.

Posted on Sep 03, 2008

  • Maanita Chadha
    Maanita Chadha Sep 03, 2008

    If the washing machine can't drain the water out then it will stick on the rinses, or it will abort with an error code.Try to reset the maching by unplugging it for an hour and then remove the cloths then turn on the unit and try to drain the water, that should take care of it

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Duet. What does F8E1 code indicate needs to be done to restore operation?


Check out the Link and the info below.
Question: Front Load Washer - Error Code - F8 E1 or LO FL Answer Product Symptom:
Front Load Washer - Error Code - F8 E1 or LO FL


F8 E1 or LO FL Code in display:
No water detected entering washer after 13 minutes, the pressure switch input has not been detected.
If the washer has an F8 E1 error or LO FL error, the door will be locked, and the control will be unresponsive. The washer will start a drain routine which takes approximately 8 to 10 minutes, during which time the pump will run continuously. The control will not accept any input during this time. Please wait 10 minutes before trying to perform any functions.
Check the water supply:

Turn on the water. Check the household water supply to see if the hot and cold water faucets are turned on. Make sure to open both faucets completely for proper fill.

NOTE: Both Hot and Cold water must be supplied to the washer.

Whirlpool recommends that appliances be direct connected to the water supply for optimum machine performance.
If a "flood saver" device is being considered:
  • Check with the manufacturer of the device to ensure it will not affect the performance of the appliance.

  • Whirlpool has experienced that "flood safety" devices can interfere with the performance of the appliance. Whirlpool typically does not recommend these devices.
Two types of "flood-saver" devices, hoses and valves are illustrated below. anti%20flood%20hose%202.jpeg floodsafe%203.jpeg Whirlpool Duet Washer F8 Code Appliance Repair Forum

Jan 19, 2016 | Whirlpool Washing Machines

1 Answer

Error code Sd (or 5d)


It means Suds Lock(Overdose of Detergent Detected During The Wash Cycle).If suds are detected continuously by the pressure switch during the drain or spin phases,the washer will fill 4 litres of water and during 5 minutes the unit will rest without tumbling,the water will be drained and it will try to spin or drain again.

If too much detergent was used:
– Run the unit through a Rinse/Spin cycle.
– Run a Normal cycle without adding any detergent.
This should clear the unit of the excess detergent.
1. Check the drain hose and make sure it is not plugged or kinked.
2. Unplug washer or disconnect power.
3. Check wire harness connections to the drain pump,pressure switch and Central Control Unit(CCU).
4. Check/clean drain pump filter of foreign objects.
5. Plug in washer or reconnect power.
6. Check drain pump.
7. Check the pressure switch.
8. Verify CCU operation by running a Diagnostic Test.

Apr 11, 2010 | Whirlpool Duet Sport HT WFW8400TE Washer

1 Answer

Water pressure for Washer (rinse only)


you nead to turn off both cold and hot water.next you nead to remove cold water hose from washer.remove screen and clean it and replace it.hookup cold water hose to washer and turn water back on.you should have better pressure.your rince cycle is cold water.

Nov 18, 2009 | Kitchen Ranges

1 Answer

Error E20 showing ........stops during wash cycle and clothes not dry on drying cycle


not familar with the code but usually wash has a built in thermo stop to wait for water to heat to correct temp,if it works normally in a rince cycle and spins out and finishes properly i would look at heat element or stat,hope this helps

Apr 06, 2009 | Zanussi ZJD1219 Front Load Washer / Dryer

1 Answer

My brand new Bosch is not draining and is showing E:13 error code


Put the washer on cold and run "TWO" cycles. There is too much soap or fabric softner.

Mar 28, 2009 | Bosch Nexxt 300 Series WFMC2201UC

1 Answer

Fabric Softner not leaving dispenser


Run some vinger through it. Fabric Softner leaves a filmy residue that can clog it up.

Jan 11, 2009 | LG DLE5932W Electric Dryer

1 Answer

Bosch Nexxt 500 Series Washer Will Not Add Water


during a normal wash cycle the washer stopped and gave an e;4 error code

Dec 21, 2008 | Bosch 3.81 cu ft WFMC530 1UC Nexxt 500...

2 Answers

F20 Error code


be sure to ck fill hoses make sure both are turned on all the way ..remove hose at washer end ckd screen inside inlet for sand/rust/gunk pull screen out to clean and be sure to reinstall it or you're asking for trouble down the road..also ck faucet end just in case someone installed one there 2..by the way just having cold water only on will cause same problem

Aug 26, 2008 | Kenmore 46462 Front Load Washer

Not finding what you are looking for?
Bosch Nexxt 300 Series WFMC2201UC Logo

1,933 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Tim Whalen

Level 3 Expert

3072 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...