Question about Indesit Washing Machines

1 Answer

Model widl 126s wash/drier. module blown up new module cost minus eprom what is an eprom anyway! is £110 how can they charge nearly half the price of a new machine? price check at comet for later machine just over £300

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,462 Answers

I agree - an absolutely crazy situation. however be wary about replacing the module. they can blow up because of a fault on another part like the motor short to earth

Posted on Aug 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer very noisy in spin cycle


maybe there 's just something with the spinning motor...try applying some grease..

Feb 19, 2014 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Indesit washer/dryer widl 126s


Hi gmarf....to reset your machine to cancel those symptoms, Unplug your machine from the Wall Outlet for a minimum of 1 minute. Upon restoring power, it should be reset and ready-to-go.....If you have any further questions or issues please update your post....good luck my friend

Aug 12, 2007 | Indesit W 123 Front Load Washer

1 Answer

WIDL 126s Wahing machine fault


could be mains filter . unplug from wall and remove top look at where the cable goes into machine are any of theses wire's burned . keep a note of were they go .

Feb 12, 2010 | Indesit W 123 Front Load Washer

1 Answer

Drain pump not working i have a new drain pump voltage to it is around 70v ac


recently the water would not drain from my indesit WIDL 126S machine, I have done all the obvious checks, everything looks as it should be. after doing a little research somethings pointed to the pump maybe being past its life span. so i have replaced it, and still its not working.
when machine is in cycle alams 2 and 4 flash, when drainage is required then machine stops what it is doing.
when machine is selected for drainage only, door locks and few minutes later door unlocks with water still in machine.
the machine is about 5 yrs old, is it time for a new one? or is there something else that may be worth checking?

Oct 05, 2009 | Hoover Washing Machines

1 Answer

I do i stop the indesit widl 126 mid cycle?


Open the door - or press stop/cancel.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jun 28, 2009 | Washing Machines

1 Answer

Indesit WIDL 106 wont start -ON/OFF-Door Led Flashes rapidly


It is a defectiv controller pcb. I think the eeprom on the controller pcb lost its program (happens often on Indesit machines).

The only solution I know is to change the controller pcb, - not a cheap solution.
I have the same problem with WIDL 106.

Dec 01, 2008 | Indesit W 123 Front Load Washer

1 Answer

Diplomat washer drier


all you have to do is:
select half load
set drier timer to required time. set main timer to dry program

i suspect you are not pressing half load button - this is essential

Jul 20, 2008 | Washing Machines

1 Answer

Indesit WIDL 102


almost certainly a new module and eprom. these modules have given a lot of problems.

not really worth doing

Jun 25, 2008 | Indesit W 123 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Indesit Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

neilmoto

Level 2 Expert

75 Answers

Are you an Indesit Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...