Question about Thermador 37 in. SGSX365 Gas Cooktop

1 Answer

Ignitors Continue to Spark

The ignitors continue to spark even after the burners are lit...we have clean both the Ignitor and the base of the burner.

Do I need to replace the ignitors? and if so how?

thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Turn the knob back towards off about 1/8 of a turn and you will take it off lite and it should fix it.

Posted on Oct 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Jenn-Air JDG8430 Ignitor won't stop sparking after burner ignites


Test the ignitor first, if the ignitor does not spark should be the ignitor itself.

Oct 12, 2008 | Jenn-Air 30 in. JGD8430A Gas Cooktop

2 Answers

Miele LP cooktop: we turned the power to the range off. when we turned on again it didn't ignite (it has power!)


Hello

Keep the air holes around the burners free of debris and grease by clearing out the holes with a thin piece of wire or a toothpick. Cleaning out the holes helps the ignitor light the cooktop

Listen for the clicking sound of the ignitor, then turn off the burner if you don't hear the clicking.

Turn the burner to the "Off" position, if you continue to hear the ignitor tick after you've lit the burner. Turn the burner back on to relight it. Ignitors normally make a brief series of electrical clicking sounds when you turn on the ignitors.

Let the ceramic igniter dry out if it has gotten wet and the burner won't ignite. If the igniter isn't wet, clear out the little holes in the burner by chipping out any blockage with a straightened paper clip.

Clean the electrodes if the burners still don't light. The electrode is in the burner base. Clean the metal part with a soft cloth. You can use emery board on the metal part but not the white ceramic part.

Nov 03, 2010 | Miele 30 in. KM443 Electric Cooktop

1 Answer

Spark ignitors on ge jgp636 either don't work or lght wrong burnr


Electric gas igniters sometimes get stuck in one position causing a clicking sound. The clicking sound that you hear is the electric arc that is pulsing from the igniter conductor (wire) to ground (the gas burner). It receives power from the electrical outlet that the stove is plugged into.
Residue from food and sometimes cleaning products may be preventing the igniter from producing a spark (Arc) to the base of the burner. This is a common problem that occurs when the stove has been cleaned or food is allowed to build up. Make sure that the igniter and the burner base are clean and dry. This will help with proper operation. Oven cleaner and a small tooth brush may be used to accomplish this. Another problem with ignition may occur if you have too little (touching) or too much space between the igniter and the base of the burner; it will prevent the burner from igniting. You should only have a little more space than the thickness of a nickel between the burner base and the igniter. A good “blue” arc from the igniter to the burner base is optimal. If this doesn’t work, you may need to replace the electric igniter module. Good luck.

Dec 19, 2009 | GE Profile JGP636 Gas Cooktop

2 Answers

G.E Profile gas cook top #JGP640 ignitor.


It is sparking because the module does not sense the heat which would normally cause the sparking to stop.

It can be caused by a poor ground, make sure the ignitor at that burner is clean and free from any obstructions. If it is then it could either be a defective ignitor or spark module.

Mar 12, 2009 | GE Cooktops

1 Answer

Viking Gas Burner issue?


is this a sealed burner unit? if so the burner base (the heavy brass part under the burner cap) has to be sitting just right. you will notice that it has holes around the the sides make sure that where your ignitor sparks to it that it aligns with the lowest hole on the burner base. if you have a great flame all around the burner after checking what i mentioned i would replace the spark module. if it continues to drive you crazy with the noise - just unplug it. the burners will continue working fine without power.

Dec 23, 2008 | Viking 42 in. Professional Series...

1 Answer

One of four dials doesn't spark ignitors...


its a spark switch gone bad, 1 switch will turn on all four burner electrodes(its just easier 1 module)sometimes model dependant you can eplace justone switch, sometimes they come as a complete set

Feb 24, 2008 | GE 30 in.Profile JGP945 Gas Cooktop

2 Answers

Ignitors continue to ignite on other burners


the igniter switch are stuck /need clean contactor of the igniter .

Jan 08, 2008 | Jenn-Air 30 in. CCG2423 Gas Cooktop

3 Answers

Jenn-Air Gas Cooktop Model CVGX2423


you will need to contact your certified local service tech.you might have a distributor problem at yor ignitor box.if the problem is not with your ignitors.

Jun 30, 2007 | Jenn-Air 34 in. Expressions CVGX2423 Gas...

Not finding what you are looking for?
Thermador 37 in. SGSX365 Gas Cooktop Logo

929 people viewed this question

Ask a Question

Usually answered in minutes!

Top Thermador Cooktops Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Controlfrk
Controlfrk

Level 2 Expert

304 Answers

Are you a Thermador Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...