Question about Top Knobs Door Pull - Oil Rubbed Bronze - M849

1 Answer

Door Knob Problem

I have a problem with my cupboard door knob, it started loosening.

Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

Usually this is quite an easy problem, just open the cupboard or drawer the knob is connected to, take a star screw driver and tighten the screws of the knob from the inside, this should solve your problem.

Please rate this solution if it helped you,
Thank you,
J.

Posted on Aug 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my hinged cupboard door stay closed?


Depends on type of hinge, If it swings back open after you closed it then either the cupboard is not level (old style hinge)...
Or the spring inside hinge is bad/broken and not holding it closed. If the door opens back just a bit (1/2 inch or so) see if hinge has adjustable screws.

Oct 15, 2016 | Top Knobs Hardware & Accessories

1 Answer

How to remove gatehouse door knob?


Look for a small set screw on the side of the deadbolt on the inside of the door loosen the set scrww and remove the cover to expose the screws that hold the door knob on

Oct 31, 2013 | Gatehouse Springfield Satin Nickel...

1 Answer

I have 3 door knobs on outside doors that are loose and need to be tightened. the knobs have come completely off sometimes when we go out the doors. how do I tighten the knobs so they are not loose?


On the inside side of the door knob, there is a decorative plate. Depending on which model door knobs you have, it is held on with a "set-screw" that might require an allen-wrench (looks like an 8-sided tool; usually in an L-shape), or just simply a screw driver, to loosen and remove it. Once you take the decorative plate off, there will be two very obvious screws that hold both sides (inside and outside) of the door knob together. Tighten these screws to tighten your knobs, then put the decorative plates back on again.

Feb 27, 2011 | Kwikset Professional Door Lock...

1 Answer

Hello all fix ya experts i have a falcon door lock this jammed and i need to know how to disassemble this lock so i can put on a new one thanks very much kim


Hello there:
the first thing that you need to do is use your tool if you have it and on the door knob look for a flat silver slot and press in on it and the door know will come off.
Next use the pointed tip and look at the plate that covers the door hole and you will see a small hole put the point in the hole and just like a wrench turn it to the left to loosen it just like a nut and it will loosen up now just spin it off ond there will be a plate under neath this top plate so take this off.
next you will be able to push the know out and this will release the lock assembly
Now you are done this is a very easy door knob to work on ok?
just replace the new door knob following the instructions ok?
I really hope that this has helped you out ok
best regards michael

Nov 06, 2009 | Hardware & Accessories

1 Answer

Door starts and stops immediately i sprayed the tracks and it worked for about a week but now it's back to starting and stop[ng prematurely


With most garage door openers, you can look under the light bulb cover and you'll find two numbered knobs. These knobs set the motor torque/speed ratio. Basically, if the door is really smooth having the knob turned down will make the motor go faster. Turning the knob up will give the motor move "oomp" but it will move a little slower. One knob adjusts the power going up and the other knob adjusts the power going down. This basically depends on how good the springs are working on the door itself. So just adjust the knobs until the motor is running each direction "comfortably".

Nov 01, 2009 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Want start unless you slam lid or push start knob in and out


HI, Check and see if the door hinge screws are tight. Sometimes the hinge loosens and the lid switch will not activet properly. It the lid is tight, you might have a lid switch going bad. The lid switch is located under the control panel. There is a screw in each corner of the control panel in the back side. Loosen these screws and lift the control panel up and it will rest on the hinges.
Ths lid switch is to the left and should have three wire to it. Parts# 8318084
I hope this helps you. If I can assist you further or you need a place to order the lid swtich, please give my web site a chance at www.whirlpoolpartssurplus.com

Thanks
Vic

May 22, 2009 | Washing Machines

1 Answer

Stuck Door Knob with No Access!


I agree with your Hacksaw method. Very easy and very fast. You are going to want to replace the knob anyway so this does not happen again. Just Hacksaw that knob as close to the door as you can without damaging the door. From there you are on your way to access to the parts of the lock. Now you can replace that knob and never have this trouble again!!!! One less headache in Life......Hope this helps you ........Joe

Jan 10, 2009 | Hardware & Accessories

2 Answers

I have a whirlpool duet washer and dryer the dryer lights all come on but I get a beeping sound and dryer will not start


try to unplug the dryer for 5-10 minutes this should reset the board. if not take off the bottom panel and test the resistance of the thermistor ( the tech sheet is in the bottom there or up top)

Dec 09, 2008 | Whirlpool GEW9250 Electric Dryer

1 Answer

How To Fix a Knob Hole


Tightening the knob screws works for me.

The screws are located in the inner part of the cupboard, just hold the knob with one hand and with a screw driver tighten the screws without applting to much force.

Aug 28, 2008 | Hardware & Accessories

1 Answer

Hole is to Small


It's actually quite simple, all you need is a drill and the right size or drill bit.
Choose a drill bit a about the size of the hole required, if you are not sure, choose a smaller size, it's easier to make a hole bigger.

Take apart the old knobs, from the inside of the cupboard, use the drill make the old holes bigger.

Attach the new knobs.

Congratulations, you did it :-)

Aug 28, 2008 | Top Knobs Back-To-Back Door Pull -...

Not finding what you are looking for?
Top Knobs Door Pull - Oil Rubbed Bronze - M849 Logo

Related Topics:

263 people viewed this question

Ask a Question

Usually answered in minutes!

Top Top Knobs Hardware & Accessories Experts

Scott Jelt
Scott Jelt

Level 2 Expert

44 Answers

Rob Benoit
Rob Benoit

Level 1 Expert

14 Answers

Are you a Top Knobs Hardware and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...