Question about Campbell Hausfeld Maxus 3/4" Impact Wrench

1 Answer

Wrench Maintenance how does oiling the wrench helps?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

In line oiler Lubrication is critical to extending the life of your valuable air impact wrench and increase productivity. An air tool that has not been properly lubricated will result in low power output. The usual culprit is a dry motor starving for some oil. Your impact wrench is an expensive investment and you must take the time to properly lubricate it. The easiest and quickest way to make surein line oiler it is constantly lubricated is to install an in line oil lubricator. One of these will insure your air tools are receiving oil every time they are used. In line lubricators attach right into the air hose and you fill them with the correct lubricating oil. (see your manufacturer's specs.). You should also do routine external lubrication through the hammer case grease fitting. A well lubricated air impact wrench will deliver more torque, last longer, run quieter and increase productivity. Don't forget to add an in line oiler to your next impact wrench or air tool. It will pay for itself several times over.

Posted on Aug 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much 30 wt oil goes in a cleco impact wrench md# wp2109


Just enough to barely cover the top of the lugs on the anvil. About 1.5 ounces.

Sep 14, 2012 | Cleco Spline Drive 1" Impact Wrench / Gun...

1 Answer

Do I need to put oil in a brand new Titan 24volt impact wrench


I have never used that brand of impact, but I have used many others and I have never known an electric impact or drill to need oil. You need oil in an air powered impact because the air motor needs lubrication. The electric motors in electric impacts have sealed bearings and brushes that are meant to run dry. The actual impact assembly should be sealed as well, it should not need any oil.

Jul 13, 2012 | Titan 24v Cordless Impact Wrench

1 Answer

Oiled and still runs slow


Vanes in the air motor not sealing well

Aug 01, 2011 | Ingersoll Rand 1/2? Heavy-Duty Air Impact...

2 Answers

As soon as the air is connected wrench starts turning. No trigger control. Thanks!


a rubber seal/o-ring is either wore or broke inside or one of the internal components are stuck, do you regularly oil it? put a couple drops of oil in where you connect the air line and let it work itself through with it turning. Might loosen it up

Jan 18, 2011 | Sears SK Pro Gun 1/2-inch Impact Wrench...

1 Answer

How do I lubricate my new DW293 DeWalt Impact Wrench, and with what oil/grease? The manual I got with the tool says to take to an authorized service professional, which I don't want to do


Its newmatic right just put a few drops oil right down the air feed and a moisture trap inline off the compresser would be goodHowever the picture looks like its electric and you don't realy have to do that now its prelubed and shouldn't be an issue for many hours of service. If it is air then wd 40 works fine the problem comes in when they sit with out use for long peirods of time they rust and seize and thats hard to fix

Dec 29, 2010 | Dewalt "Heavy Duty 1/2" Impact Wrench

1 Answer

Will not remove lug from autos.Motor spins nothing else is happening Ibought the TL 100200RB


An impact wrench has "hammers" that strike an anvil. If you have not been lubricating your impact at times, or if you have a large amout of condensation in your air (water) then it could be rusted. The motor will still spin, but you don't get any "impact" action. Try putting some light air too oil in the air line and if there is a plug for oil, fill it also. Allow to soak and try it again. If it is that bad you might have to dis-assemble, and clean throughly

Jul 03, 2010 | Campbell Hausfeld 1/2" Impact Wrench -...

1 Answer

Oiling a Sears 900.275132 impact wrench


use air tool oil and put a couple of drops where the air plugs in.

Feb 21, 2010 | Sears Impact Wrenches & Drivers

Not finding what you are looking for?
Campbell Hausfeld Maxus 3/4" Impact Wrench Logo

Related Topics:

662 people viewed this question

Ask a Question

Usually answered in minutes!

Top Campbell Hausfeld Impact Wrenches & Drivers Experts

River bottom

Level 2 Expert

174 Answers

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

John Trevino

Level 3 Expert

1378 Answers

Are you a Campbell Hausfeld Impact Wrench and Driver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...