I am trying to add station 73 to the SANYO TV set and the set will not allow it. The stations only go to 68.
Can you tell me how to do that?
pg 13 of inst. book, item 3 says to add cable chs hold the 1 key until C1 appears then enter the other 2 numbers...in my case it would be 73 which I need to get my DISH channels on this TV
An expert who has achieved level 3 by getting 1000 points
An expert that got 10 achievements.
An expert that got 5 achievements.
An expert that has over 10,000 points.
Re: Add a station
Might it be that you need to add Channel 73 to the receiver box of your DISH Network? If you have such a receiver box, then the channel selection is done on that box and the Sanyo TV set is for viewing it output. This could be verified if the Sanyo is set to AV/Video input and changing channels are displayed not on the Sanyo but on the DISH receiver box.
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.
Good luck and kind regards. Thank you for using FixYa.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Press Menu on the TV (second button from the left) or the remote. Use the Vol + / Vol - buttons to highlight Tuner, only available when the input is the TV (press TV/AV to get to the correct source) mode. Press Ch+/Ch- to highlight AutoProgram and then Vol+ to start the search for channels. The TV will show Tuning Finished when done and then go to the lowest channel found. If you want to add or remove stations, tune to the desired channel, then press Menu, and highlight Tuner, Ch+/Ch- to highlight Add/Erase, then Vol+/Vol- to set Add or Erase. Press TV/AV/Exit to get out of the menu.
When I had Dish hooked up I had to use chanel 3 on my television or the video inputs. The Dish box will take care of all the stations that yor receive. You shouldn't have to change chanels with your tv.
I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread. If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!
Basically, you cannot use the coax connections for both the VCR and the RCA converter box. I would hook up the phono/cinch connectors from the VCR to the TV if you can (these are also called RCA connectors, but I'm avoiding using that name so we dont confuse the digital receiver with a cable/connector name that is the same here). There should be a yellow one for video and red/white ones for left and right stereo. I believe the RCA converter comes with a three headed cable that can do this for you. With this configuration, you can set the TV to input on these connectors and the VCR should always output there. Once that is set, you can still use the converter box to receive the signal from your antenna, then run the coax to the VCR. Now, the VCR will always have to be set on channel 4 in your setup and you will need to manually change channels on the converter box for it to record a show. Does this make sense so far?
Assuming that you tried to tune stations onto the UHF bandwidth and received nothing,Commonly the tuner box is probably at fault and needs replacement. The VHF and UHF signals are split inside the tuner so if you receive VHF fine then UHF should as well unless faulty of course. Some circuits require an external IC to do the switching, but more on the older models. Regards and good luck, JUS004
If you are on outdoor antenna or rabbitt ears this cannot be done as most tunersonly go to channel 69 . If your are on cable this can be achived by going into the menu and first making sure the tv is in the cable mode . Your set should have a section for manuelly adding or deleting or channels , simply by pushing 73 with your remote then using the onscreen menu to add this channel . Or you can just autoprogram your channels over again and this should pickup your channel . If this does not work what is the model # of your set so i can lookup the manuel if it is available. Also you can try to google the model # of your set with the phase (owners manuel) to see if you can find a free download of your set .This will also have the info your looking for . Good luck