Question about D-Link Super G with MIMO (DI-624M) Router (DLKDI624M)

1 Answer

D-link dl-624 tryed to factory default then ip address http://192.168.0.1. then put admin in user name then ok nothing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Check on computer what ip address router is assigning computer.If not reset router it should set it back to factory defaults.

Posted on Aug 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does the d-link airplus xtreme g model DI-624 support WPS?


yes there is RESET or WPS button for RESET all settings to factory defaults. For that press RESET/WPS button for 1 seconds it is in the back side of router. Then all settings defaults . You need to configure your router with below method. Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.1.1 or http://192.168.0.1 or http://192.168.15.1 or http://192.168.2.1 If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router. If you are still not able to access router with above ip then you need to RESET it for that press RESET button for 10 seconds it is in back side of router then all settings defaults..Then you can access it with above method. Then set WAN settings as internet service provider settings enable DHCP. .Click on wireless and enabled it. Then click on wireless->wireless security->WEP security there is code password note down it or enter new password then save setting s and restart router. then you can connect wireless with new password. Let me know if you need further assistance. Thanks for using FixYa.

Mar 03, 2011 | D-Link AirPlus Xtreme G DI-624 Wireless...

1 Answer

Its asking password for this ip address 192.168.0.1


The IP Address 192.168.0.1 is the address of the modem.
The Manual advises to enter admin as the User name, leave the password blank and click OK.

See page 12 of the manual Product Manual (5.0 MB) - D-Link AirPlus Xtreme G DI-624

Feb 09, 2011 | D-Link AirPlus Xtreme G DI-624 Wireless...

3 Answers

What is the Dlink DI-624 default password


Here is a site that will help you most of the D-Link routers: http://www.default-password.info/d-link/
Here is an extract: D-Link DI-624 - all admin (none) - Admin access (HTTP) User (none) - Admin access (HTTP)

Feb 02, 2011 | D-Link Routers

1 Answer

My son push the reset on my D-Link router. trying to follow directions... none of the addresses work. http://192.168.1.1 or http://192.168.0.1 how can I configure this router?? help!


Dear User ,

Once the Router is Reset it goes back to the factory settings , In this Issue you have mentioned both D-link router and a gateway Wireless B router . Following is the default password and Ip addresses of both routers :

1.
Gateway Wireless B-Router

Default Ip : 192.168.1.1

User Name : admin
password : admin

2. D-Link Router :192.168.0.1

User name: Admin
Password : Admin

Please let me know if it worked

Thanks and regards
Aboobacker sidiq
Internet explorer Specialist

Nov 28, 2010 | Gateway Wireless-B Router (wbr-100)

1 Answer

When i run wisard it ask about old passworld


This FAQ is for the DI-514, DI-524, DI-604, DI-614+, DI-624, DI-624M, DI-624S, DI-774, and DI-784.

Step 1 Open a web browser and enter the IP address of the wireless router in the address bar (default is 192.168.0.1). Press Enter.

Step 2 The username is admin and the default password is blank (nothing). Click OK.

Step 3 Click the Tools tab and then click Admin to the left.

tools_admin.gif

Step 4 To change the administrative password, enter a new password in the Admin section.

To change the user password, enter a new password in the User section.

Step 5 Click Apply then click Continue to save the settings.

Note: If you forget your password, you can reset the unit to factory defaults.
Click here for instructions.

Nov 02, 2010 | D-Link AirPlus DI-524 Wireless Router

1 Answer

Looks like router has reset. I can logon as user,


Trying using the below:

Open up a browser and type in the url address:

http://192.168.0.50

IP Address - 192.168.0.50

User name - admin
Password - (leave blank)

Jul 16, 2009 | D-Link AirPlus Xtreme G DI-624 Wireless...

7 Answers

DI-624 can't login as admin


I was ready to give it up and pitch the thing, but I found this on another board and it worked:

login - admin
password - password (not blank)

Aug 08, 2007 | D-Link AirPlus Xtreme G DI-624 Wireless...

1 Answer

How do I open a range of ports on my VDI-604 or VDI-624 using firewall rules?


Step 1 You will need the IP address of the computer that you want to open ports to. How do I find the IP address of my computer? Step 2 Open a web browser and type the IP address of the VDI-604 or VDI-624 in the address bar (default is 192.168.0.1). Press Enter. Step 3 The default username and password is listed below for your version of firmware: VDI-604 firmware 1.05F/VDI-624 firmware 2.39DDM - The default username is admin and the default password is blank (nothing). VDI-604 firmware 1.07 Build 28/VDI-624 firmware 2.43 Build 12 - The default username is admin and the default password is password. Click OK. Step 4 Click the Advanced tab at the top and then click Firewall on the left. Step 5 Select Enabled and configure the following: Name - Enter a name to identify the rule Action - Select Allow Source Interface - Select WAN Source IP Range Start - Enter an IP address or * to allow this rule to apply to all incoming IP addresses. If you are opening this rule to a series of IP addresses, enter the first IP address in the range. Source IP Range End - If you are opening this rule to a series of IP addresses, enter the last IP address in the range. Destination Interface - Select LAN Destination IP Range Start - Enter the IP address that you obtained in Step 1 Protocol - Select the protocol (TCP, UDP, or Both) Port Range - Enter the starting and ending ports that you want to open Schedule - Select Always to apply this rule all the time or Schedule to specify a schedule Step 6 Click Apply and then click Continue to apply the new rule.

Feb 16, 2006 | D-Link AirPlus Xtreme Super-G DI-624...

1 Answer

How do I open a range of ports on my VDI-604 or VDI-624 using firewall rules?


Step 1 You will need the IP address of the computer that you want to open ports to. How do I find the IP address of my computer? Step 2 Open a web browser and type the IP address of the VDI-604 or VDI-624 in the address bar (default is 192.168.0.1). Press Enter. Step 3 The default username and password is listed below for your version of firmware: VDI-604 firmware 1.05F/VDI-624 firmware 2.39DDM - The default username is admin and the default password is blank (nothing). VDI-604 firmware 1.07 Build 28/VDI-624 firmware 2.43 Build 12 - The default username is admin and the default password is password. Click OK. Step 4 Click the Advanced tab at the top and then click Firewall on the left. Step 5 Select Enabled and configure the following: Name - Enter a name to identify the rule Action - Select Allow Source Interface - Select WAN Source IP Range Start - Enter an IP address or * to allow this rule to apply to all incoming IP addresses. If you are opening this rule to a series of IP addresses, enter the first IP address in the range. Source IP Range End - If you are opening this rule to a series of IP addresses, enter the last IP address in the range. Destination Interface - Select LAN Destination IP Range Start - Enter the IP address that you obtained in Step 1 Protocol - Select the protocol (TCP, UDP, or Both) Port Range - Enter the starting and ending ports that you want to open Schedule - Select Always to apply this rule all the time or Schedule to specify a schedule Step 6 Click Apply and then click Continue to apply the new rule.

Feb 16, 2006 | D-Link Express EtherNetwork DI-604 Router

1 Answer

Parental control


The following types of parental control can be configured on the VDI-604/VDI-624: Domain Blocking URL Blocking -------------------------------------------------------------------------------- Domain Blocking Domain Blocking will allow/deny access to certain websites. Step 1 Open a web browser and type the IP address of the VDI-604 or VDI-624 in the address bar (default is 192.168.0.1). Press Enter. Step 2 The default username and password is listed below for your version of firmware: VDI-604 firmware 1.05F/VDI-624 firmware 2.39DDM - The default username is admin and the default password is blank (nothing). VDI-604 firmware 1.07 Build 28/VDI-624 firmware 2.43 Build 12 - The default username is admin and the default password is password. Click OK. Step 3 Click the Advanced tab at the top and then click Parental Control on the left. Step 4 Below Parental Filters, select Domain Blocking. Step 5 Below Domain Blocking, select Allow users to access all domains except "Blocked Domains" to only allow to all websites except those listed or select Deny users to access all domains except "Permitted Domains" to only allow access to the websites listed. Step 6 Enter the website (i.e. disney.com) below the option you selected in Step 5 and then click Apply. -------------------------------------------------------------------------------- URL Blocking URL Blocking will prohibit access to websites than contain certain words. Step 1 Open a web browser and type the IP address of the VDI-604 or VDI-624 in the address bar (default is 192.168.0.1). Press Enter. Step 2 The default username and password is listed below for your version of firmware: VDI-604 firmware 1.05F/VDI-624 firmware 2.39DDM - The default username is admin and the default password is blank (nothing). VDI-604 firmware 1.07 Build 28/VDI-624 firmware 2.43 Build 12 - The default username is admin and the default password is password. Click OK. Step 3 Click the Advanced tab at the top and then click Parental Control on the left. Step 4 Below Parental Filters, select URL Blocking. Step 5 Below URL Blocking, select Enabled, enter the word, and then click Apply.

Feb 16, 2006 | D-Link AirPlus Xtreme Super-G DI-624...

Not finding what you are looking for?
D-Link Super G with MIMO (DI-624M) Router (DLKDI624M) Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Routers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Mike

Level 3 Expert

4331 Answers

Christopher Thrash

Level 3 Expert

425 Answers

Are you a D-Link Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...