Question about Canon PIXMA MP780 All-In-One InkJet Printer
The display say: "SATURAZ.CONT.INCH" what can i do?
SOURCE: Canon Pixma MP780
Yep your printer is nearing service time. This involves changing the waste ink pads and resetting it.
you could reset the printer without changing the wate ink pads but you risk damaging it
What i do is take the pads out wash them and replace them.
the waste ink pads are the pads the cartridge rest on whan itsn in neutral position
THE SERVICE MANUAL FOR YOUR PRINTER *step by step instructions in repairing it) is here
Posted on Dec 31, 2007
Go to this link. Wait a few seconds for all the files to load. Select your OS in the box, then wait a few more seconds, and you will see the drivers displayed.
You will need to download and install both the driver and the MP Navigator (under the Software heading). Click on the link and follow the instructions to install.
Posted on May 20, 2008
I tried the other solutions listed here - and no luck. After cleaning the inside of the ADF, like the manual suggested - no change. How are you supposed to do that anyway? Deep cleaning the inside of the machine also has nothing to do with it.
I finally figured out why things that I copied with the ADF had lines/marks on them, but those placed directly on the platen (big glass) were fine. When you copy with the ADF, the copy is not being made from the large glass area. Rather, there is a thin glass area right next to it.
Turns out, there were a couple of smudges (goo) on that thin piece of glass which were creating long vertical lines down every sheet. Cleaned the glass - problem solved!
Gosh, I hope this helps someone else save some time, and frustration.
Posted on Dec 03, 2008
SOURCE: need to print darker black copy
Click Start, Click control panel, click printers and faxes, right click your printer, click properties, click printing preferences (near bottom of window), change print quality to high, click apply, click ok, close all windows and try. this will slow the printer slightly.
Posted on Jul 05, 2009
This is the Automatic Sheet Feeder [ASF] Cam Sensor Error
Movement may cause the plastic guide to move away from the chassis which causes the gears not to rotate properly causing a grinding noise and 5 alternating blinks (SFP) or ##356 (MFP) - ASF Cam Sensor Error.
Remedy: Adjust the Screws & Main Case Unit
Step 1: Remove the Left & Right Covers and the Main Case Unit (main cover).
Step 2: Remove the 4 mounting screws from the Chassis.
Step 3: Remove the Main Unit from the Bottom Case.
Step 4: Turn the Main Unit over (upside down) and place on work surface.
Step 5: Inspect the ASF section of the Main Unit for a gap between the white plastic guide and the Chassis. The size of the gap varies. Even if the gap is not visible, complete the steps below.
Step 6: Disconnect the appropriate cables and remove the Logic Board from the Chassis.
Step 7: Loosen but DO NOT remove the 4 mounting screws which can be located behind the logic board on the Chassis.
Step 8: Reseat the white plastic guide so it sits flush against the Chassis. The tip of the white plastic guide should sit slightly inside the mounting screw hole. When seated correctly, the gap will no longer be present.
Step 9: Tighten the 4 mounting screws without causing the plastic guide to shift.
Step 10: Reassemble the printer and retest.
Posted on Oct 01, 2009
Tips for a great answer:
Dec 16, 2010 | Canon PIXMA MP780 All-In-One InkJet...
Jun 06, 2010 | Canon PIXMA MP780 All-In-One InkJet...
Nov 04, 2009 | Canon PIXMA MP780 All-In-One InkJet...
Apr 03, 2009 | Canon PIXMA MP780 All-In-One InkJet...
Dec 21, 2008 | Canon PIXMA MP780 All-In-One InkJet...
Nov 17, 2008 | Canon PIXMA MP780 All-In-One InkJet...
Jul 11, 2008 | Canon PIXMA MP780 All-In-One InkJet...
Apr 05, 2008 | Canon PIXMA MP780 All-In-One InkJet...
Dec 23, 2015 | Canon PIXMA MP780 All-In-One InkJet...
198 people viewed this question
Usually answered in minutes!