Question about Heating & Cooling

1 Answer

Retired 70 yr ol with health problems husband in jail for l and l petifal[unknow to me] lost his income and unableto work my self .high bills unable to buy fuel or maitain home also highproperty tax ;high morage on house with car and house insurance

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 500 questions.

  • Expert
  • 540 Answers

This is not an A,C. problem, this is a personal problem! Thank-you-very-much!

Posted on Aug 26, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Intertherm p5rd036k

Sounds like your tstat could use some attention. The broken bar sounds like a low battery indicator. To verify wether the tstat is working correctly you can try bridging the R and W wires (after the thermostat) to set a call for heat. Be careful when you do this as you could short or blow your circuit board and other sensitive electrical parts. The R terminal is 24v power and when you bridge R and W you send 24v to the circuit board which indicates a call for heat. W is heat Y is cooling. If nothing happens still then you should call a technician as you may have broken parts and will require replacing.

Dec 09, 2013 | Heating & Cooling

1 Answer


Sounds as though the compressor is trying to start, and then shuts off, then tries again. If this is the case...

Usually this results when the capacitor has gone bad and the compressor is unable to start or break free to run.

Basically a capacitor gives the compressor a "Bump" to allow the pistons to break-away from the stopped position. Once the compressor is operational, the capacitor circuit is dropped and the compressor functions as expected. When the capacitor goes bad, the pistons cannot move and the compressor over-amps and the internal, or external OL (overload) opens due to high amp draw. When the OL cools down it allows the compressor to try to start again. But as it cannot it will make a loud humming noise as if it were locked up.

Which brings me to my second solution.... the compressor is locked up mechanically. And the pistons have siezed or welded themselves stationary. If this is the case, and the capacitor checks out good, then the compressor will need to be replaced.

Sep 04, 2010 | LG Heating & Cooling

1 Answer

Poor cooling. High bills when heating.

see if the lines the big one if it is verry cold or frosted let me know

Apr 08, 2010 | Goodman GPC1330H21A Air Conditioner

1 Answer

Replaced condenser and had health problems. Now

Hi Bill, I am sorry you became ill from this or anything else. On a condenser, did you change out the condenser coil as in removing the freon and cutting it out, or did you remove the complete unit on top, compressor and all? If you changed out the complete unit on top, the wiring should be fairly easy to connect. Take your power in which would be 220 volts from your power source. More then likely, you will have 2- black hot wires in and a ground, either bare copper or green which grounds to the new unit case. You will have 2- new wires from the new condenser , red and black or different colors, it will not matter as each line will be 120 volts, these will be the load wires to the new unit. Connect 1- wire to one coming in, either one, and do the same to the other wire. Secure the ground and you are set. If this is what you are doing or want to do, this is the way. Once you get power to the new unit, the controls will do the rest for you. Just turn it on inside and you will be up and running. Keep me posted.

Dec 03, 2009 | Coleman Mach III Air Conditioner

1 Answer

Outside air temp around 100 unit wasnt cooling good noticed evap coils dirty cleaned them cooled alittle better checked low side showed 90 lbs had friend reclaim to get it to 70 lbs 30 minutes later it...

90 psi suction too high possible bad valves or non condensablies in the system (AIR) what is the head pressure and what type of freon r-22 410-A? your unit is never shutting off watch out for that electric bill. and did you take apart the condenser and clean it? Tom

Jun 25, 2009 | Heating & Cooling

1 Answer

My colmen central air unit is not working properly. The Outside unit is not working. The problem initally arouse in June, but it "self corrected" after having the A/C unit turned off. Since that...

If nothing is running outside at times you probably have a weak contactor coil that is not pulling the contactor in all the time. If the outside fan comes on but not the compressor, the compressor is over heating and shutting off on overload protection. This could be a dirty condenser coil, low on refrigerant, the compressor it's self. The compressor comes with a 5 yr. warranty.

Sep 27, 2008 | Coleman Heating & Cooling

1 Answer

High bills unable to buy fuel 'food and medicene and maintain home ramp slipper in winter[need solving] to prevent falls roof tiles nees replacing

Goverment help! contact your "Big Brother"! or go to the BIBLE where "GOD" sent Elisha to the widow woman cause she couldn't heat her home or buy food , same problem but different time! Thank-you-very much!

Aug 26, 2008 | Heating & Cooling

2 Answers

I have an Aloha Breeze tower fan and have lost the remote, where can I get another? The Model number is 84001. Thank you

I couldn't find anything either and then my husband calling them. There is a number in operation manual but they are close right now. Here is the number 1-800-295-4448.

Apr 19, 2008 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Heating & Cooling Experts


Level 3 Expert

2037 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Cris Sparks
Cris Sparks

Level 2 Expert

338 Answers

Are you a Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides