Question about Uniden Radio Communications

1 Answer

Scan chennels can i add extra scan channels to a uniden UH0 88 UHF if i have the frequencies.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 109 Answers

Go to Page 10 of your owners manual the section marked "open scan mode allows you to set which channels are in the open scan memory.

Pat N5SLI

Posted on Aug 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ca't program scanner


Hi Rashif,

I not familiar with you model of Uniden/Bearcat scanner, but being a uniden does simplify things a little, so here's my generic Uniden programming hints.

Firstly, press the prog key, then enter your frequency, example: 78.0250, note that I emtered (.) the decimal key between the 8 . and the 0, this is required, else you'll get ERR message on the display.

Say you wanted to enter 4680375MHz, as this is in the UHF band, you would need to press the following keys exactly as I've stated here: 468.0375, now press enter key, now press delay key, now press enter key again, you now have this frequency stored on which ever channel you chose. 1-100 or however many channels your scanner can hold in memory.

That is just an example program for you to follow, make sure that the L/O icon does not appear on the display before you press the Enter key, if it is showing, press the L/O key to turn off that icon before you press Enter.

Follow these steps one by one through your channels until you have enough frequencies of your choice programmed,
You can now press scan and listen to what ever you chose.

I hope that I have assisted you, and remember, that my hints are only generic to uniden scanners, not your model.

Cheers,
Peter

Mar 05, 2013 | Uniden Radio Communications

1 Answer

LOST MY MANUAL TO MY UNIDEN BEARCAT BC142XL CAN I GET A FREE REPLACEMENT


The manual isn't online to my knowledge however I did find a guide on how to program it.
"Turn it on. Push the "MANUAL" button to stop it from scanning.

Push number 1, then push "MANUAL" again. This should leave you on
channel one.

Using the keypad enter the frequency you want to monitor, then push
"E." Press "REVIEW" at anytime to see what frequency is programmed
there. If the review button flashes 000.0000 on the LED readout
display, you might be entering an invalid frequency. Refer to the list
of acceptable frequencies in the Frequency Range Bands below.

Push "MANUAL" to step to channel number two. Enter the frequency. Push
"E." Push "MANUAL" to step to channel three. Repeat this process until
all the (10) channels are full, or you've run out of frequencies to
enter.

Push "SCAN" to start automatically scanning the frequencies. The
radio will stop when it hears someone talking, and resume scanning two
seconds after the conversation has stopped.

Frequency Range Bands:

20 to 29.7 MHz (10 Meter "Ham" Band)
29.7 to 50 MHz (VHF Low Band)
50 to 54 MHz (6 Meter Amateur Band)
136 to 144 MHz (Military Land Mobile)
144 to 148 MHz (2 Meter "Ham" Band)
406 to 420 MHz (Federal Government Land Mobile)
420 to 450 MHz (70cm "Ham" Band)
450 to 470 MHz (UHF Standard Band)
470 to 512 MHz (UHF "T" Band)"

http://newsgroups.derkeiler.com/Archive/Rec/rec.radio.scanner/2006-01/msg00174.html
Hope this helps.

Apr 22, 2011 | Office Equipment & Supplies

1 Answer

How to program a bc855xlt uniden bearcat scanning radio


Major Functions of Uniden BC 855 XLT Desktop Scanner

RANGES AND MODES:
29-54 MHz; 137-174 MHz; 406-512 MHz; and 806-956 MHz NFM; 118-136 MHz AM

MEMORIES & MEMORY SCANNING:
• The 855 receives mainly via frequencies programmed into its 50 memory channels. It does not have a VFO or dial mode as such, but can scan within two frequencies.
• To scan memory channels, press SCAN. To hold a channel, press MANUAL.
• The 50 channels are divided into 5 banks (Bank 1: Channels 1-10, Bank 2: 11-20, etc.).
• Any of the 5 banks can be turned off from scanning. To turn a bank on/off, press its number while in Scan Mode. Active banks are illuminated in the display.
• SPEED toggles between 8 & 16 channels per second in both scan & search modes.
TO ENTER A FREQUENCY IN A MEMORY CHANNEL:
• Press MANUAL.
• Press the channel number you wish to program using keypad.
• Press MANUAL again.
• Enter the desired frequency using the keypad.
• Press E (ENTER). (If you make an ERROR, press CLEAR & re-enter frequency.)
• To set 2-second delay, press DELAY. Confirmed by “DLY” in display. Same deselects.
• To lock out channel from scan, select it & press LOCK OUT. Same deselects.
PRIORITY CHANNEL: Press PRIORITY to scan Ch. 1 every 2 seconds.
TO SELECT CHANNELS MANUALLY:
• Press MANUAL.
• Press desired channel number on keypad.
• Press MANUAL. Press MANUAL repeatedly to step through channels sequentially.
TO SCAN UP/DOWN FROM A CHANNEL: Select channel manually, then press ? or ?.
TO SCAN/SEARCH A GIVEN FREQUENCY RANGE:
• Press MANUAL.
• Enter the lower frequency limit.
• Press LIMIT.
• Enter the upper frequency limit.
• Press LIMIT.
• Press SEARCH.

I couldn't locate the manual for your scanner, but it's basically the same as the BC860XLT, except that the 860 has 100 channels. Other than that, all controls and functions are the same. You can download and print the manual for the 860 here:

http://uniden.com/pdf/BC860XLTom.pdf

For a comprehensive database of active frequencies in your area, and a lot of other useful scanning info, visit:

www.RadioReference.com

BillB

Jan 19, 2010 | Uniden BC895XLT Base Scanner

1 Answer

PROGRAM FREQ IN BC142XL


Its so easy to use you really don't need a manual for the Uniden BC
142XL scanner.

Turn it on. Push the MANUAL button to stop it from scanning.

Push number 1, then push MANUAL again. This should leave you on
channel one.

Using the keypad enter the frequency you want to monitor, then push
E. Press REVIEW at anytime to see what frequency is programmed
there. If the review button flashes 000.0000 on the display, you might be entering an invalid frequency. Refer to the frequency coverage list below.

Push MANUAL to step to channel number two. Enter the frequency. Push E. Push MANUAL to step to channel three. Repeat this process until all ten channels are programmed, or you've run out of frequencies to enter.

Push "SCAN" to start automatically scanning the frequencies. The
radio will stop when it hears someone talking, and resume scanning two
seconds after the conversation has stopped.

Frequency Coverage:

20 to 29.7 MHz (10 Meter "Ham" Band)
29.7 to 50 MHz (VHF Low Band)
50 to 54 MHz (6 Meter Amateur Band)
136 to 144 MHz (Military Land Mobile)
144 to 148 MHz (2 Meter "Ham" Band)
406 to 420 MHz (Federal Government Land Mobile)
420 to 450 MHz (70cm "Ham" Band)
450 to 470 MHz (UHF Standard Band)
470 to 512 MHz (UHF "T" Band)

For a comprehensive database of active frequencies in your area, visit

www.RadioReference.com
.

Nov 07, 2009 | Uniden BC248CLT Base Scanner

1 Answer

Have an old uniden uhf, model vh 011. Is this a 5 watt unit or not?


This radio has a 5 watt transmitter, and works on 40 channels in the UHF (477MHz) band. Called a "CB" but is not marketed for use in the U.S. since "CB" here is 40 channels in the HF (27MHz) band. "FRS" in the U.S. is the "new CB", but offers fewer frequencies and all are lower than 477Mhz. Transmitting with this radio in the U.S. (and probably other places, too) will require a license.

More information about this radio can be found below:

http://www.uniden.com.au/v3/product.asp?ID=36&Group=2

Sep 11, 2009 | Uniden Radio Communications

2 Answers

Need a free printable user manual for Bearcat scnner BC142XL


Its so easy to use you really don't need a manual for the Uniden BC142XL scanner.

Turn it on. Push the "MANUAL" button to stop it from scanning.

Push number 1, then push "MANUAL" again. This should leave you on channel one.

Using the keypad enter the frequency you want to monitor, then push "E." Press "REVIEW" at anytime to see what frequency is programmed there. If the review button flashes 000.0000 on the LED readout display, you might be entering an invalid frequency. Refer to the list of acceptable frequencies in the Frequency Range Bands below.

Push "MANUAL" to step to channel number two. Enter the frequency. Push "E." Push "MANUAL" to step to channel three. Repeat this process until all the (10) channels are full, or you've run out of frequencies to enter.

Push "SCAN" to start automatically scanning the frequencies. The
radio will stop when it hears someone talking, and resume scanning two seconds after the conversation has stopped.

Frequency Range Bands:

20 to 29.7 MHz (10 Meter "Ham" Band)
29.7 to 50 MHz (VHF Low Band)
50 to 54 MHz (6 Meter Amateur Band)
136 to 144 MHz (Military Land Mobile)
144 to 148 MHz (2 Meter "Ham" Band)
406 to 420 MHz (Federal Government Land Mobile)
420 to 450 MHz (70cm "Ham" Band)
450 to 470 MHz (UHF Standard Band)
470 to 512 MHz (UHF "T" Band

If this helps, please take a moment to give us a rating -- and a rating of "very helpful" would be greatly appreciated.

Sep 06, 2009 | Uniden BC-95 XLT Scanner

1 Answer

How do i use an inherited uniden scanner. dad didn't leave instructions.... how do i set it up? which frequency do i use? many thanks


A scanner, if used properly, can monitor frequencies as it progresses through them. If you want your scanner to monitor only certain frequencies of your choice, you can set those frequencies as the PRIORITY channels. Example: push PROGRAM then punch in frequency 152.6255 then set the mode (if nessessary) at VHF (very High Frequency) UHF (Ultra High Frequency) or FM (Frequency Modulator) or AM (Amplitude Modulator) etc. You can program as many priority channels as the scanner allows.

Hope this helps!

Jun 23, 2008 | Uniden BC72XLT Handheld Scanner

1 Answer

Channel retriving


scan the frequencies this takes time then there is a hold button to save frequensies
frequensies are pulled by the air using the scanning option when there being used by whom ever but you can go online and do a search of scanner police frequencies easy part but most are going digital encrypted which means you can not get the frequensies
you will only be able to get uhf frequencies

May 11, 2008 | Uniden BC72XLT Handheld Scanner

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Radio Communications Experts

Jason

Level 2 Expert

208 Answers

Robert McClure

Level 2 Expert

160 Answers

John
John

Level 2 Expert

509 Answers

Are you an Uniden Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...