Question about Denon AVR-1905 Receiver

1 Answer

Turns off after 4 secs or so....From Green to Red,


Turns on for a few seconds and then the power light goes red, I guess the red is stand by or protected mode. I disconnected everything and checked inside, no smell, no burning, everything looks good.

Thanks for any help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Probably one of the surround channels is blown, thats why it goes into protection, meassure output transistors with a ohm/diode meter if thers no shortcut in the base to collector
pauliesbouth

Posted on Aug 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The green light flashes when power is turned on and then flashes red and turns off. Can this be reset ?


what do i do when my DENON AVR-1506 turns on then flashes red and turns off?

Mar 08, 2011 | Denon AVR-1506 Receiver

1 Answer

I have a Denon 1708 receiver. When I push the "on" button, either on the unit itself or using the remote, the light flashes green for a few seconds, then flashes red. When it turns red, all of the info...


Your result indicates the unit is not passing its power up self test. The first thing to try would be to remove all connections to the unit and try to power up. If it still mis-behaves, the unit has an internal problem best left to pros unless you're pretty good digging through circuitry. If it comes up stable, then reconnect things one at a time until the issue occurs again. Detach the offending connection and look for issues in the cables or the connected unit.

Oct 23, 2010 | Denon AVR-1708 Receiver

1 Answer

Power button turns green, flashes and then turns red and flashes.


Hi,
While working it stops and flashes red approximately 2 seconds interval

Causes
Protection circuit is activated depending on the temperature of the surroundings

Remedy
Switch off the power supply and power on after the temperature have reduced.


While working it stops and flashes red approximately 0.5 seconds interval

Causes
1.Using speakers having less impedance than the specified.
2.If speaker core wire touch each other Protection circuit is activated


Even applying power red flashes 0.5 seconds interval

Cause
Amplifier circuit has failed

Remedy
Switch off the power and contact denon service centre


Thank You

Sep 07, 2010 | Denon AVR-789 Receiver

1 Answer

I turn my unit on and it turns off after a few seconds


After about 10 minutes of play time the power light goes from green to red and the system shuts down.

Jul 12, 2010 | Denon DRA-397

1 Answer

Power light is flashing and power won't turn on


these a couple things you can try to reset,if resetting dont work you will have a amp problem.Try pushing and holding down these 3 buttons s.speaker b and att and exit buttons for at least 3 sec or more.should reset.If not also try pushing and holding down mult speaker and exit and att buttons together for at least 3 or more seconds.if still shuts down you will have shorted transistors inside of unit.

Apr 17, 2010 | Marantz SR4002

1 Answer

Unit only stays on for 4 seconds then turns itself off.


This is a short or unstable ohm load. Remove all speaker wire connections to see if the amp will stay on.
If the problem goes away when disconnecting the speaker wires try this:
1) Check volume level on zone one and zone 2 if connected. If it is too high the amp will go into protect mode and shut off exactly as you described.
2) Make sure no wires are touching any other wire or the metal surface of the amp. This will cause a short and send the amp into protect mode.

Nov 21, 2009 | Denon AVR-1705 Receiver

1 Answer

After turning ON the power/standby switch, the unit(receiver) display comes ON (green light) then after approx.4-5 seconds the display goes OFF and the unit defaults back to the standby mode (red light). I...


Is the red light flashing at first?
The unit may be going into protect mode. Lets hope it has done the job and the receiver has protected itself from failure.
Protect mode can result from speaker wires touching each other or the Amps2_bing.gif metal case. Check that first.
It can also be caused by unstable ohm loads if too many speakers2_bing.gif are connected to any of the outputs especially zone 2.
If you can remove all speaker wires and turn the unit back on. If it stays on, turn the volume down on the main zone and zone 2 if connected. Then reconnect speaker wires.

Nov 16, 2009 | Denon AVR-485 Receiver

1 Answer

Turns off after 4 secs or so....From Green to Red,


Receiver turns on Green but on pressing button again for red light standby, red light will not come on for this Denon receiver. Recently light came on saying Panel Lock is on. I was not able to get tuner to work.

Aug 25, 2008 | Denon AVR-1905 Receiver

1 Answer

Blinking red power light


I think Denon designed in a "bug" as mine just "went east" today

May 25, 2008 | Denon AVR-1906 Receiver

Not finding what you are looking for?
Denon AVR-1905 Receiver Logo

Related Topics:

504 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio & Video Receivers Experts

 Elex
Elex

Level 2 Expert

49 Answers

jonpoint

Level 1 Expert

4 Answers

Tech Leprechaun
Tech Leprechaun

Level 2 Expert

61 Answers

Are you a Denon Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...