Question about Projection Televisions

3 Answers

Unit is dead willnot lite up - altered to a Pansat 2700, after couple of days,went dead, nothing. Would like to know where I couldsend it to get repaired. Thank you- edwinathorpe@hotmail.com

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,029 Answers

Can you check the fuse to see if the fuse is bad and replace if possible before sending it to a repair man?which region are you?

Posted on Aug 25, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,879 Answers

Or look at right side of this page and check out the ads.

Posted on Aug 25, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,800 Answers

Try to use our repair man service buy typing ur Zip code!!

Posted on Aug 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tlevision is dead


to even try to help I would need to know brand and model.

Nov 27, 2012 | Projection Televisions

1 Answer

Why won't my TV turn back on even manually??


total dead usually means the fuse---unplug the set for safety and remove back cover---follow power cord just inside and you will find the fuse in a snap in holder--check to see if bad.............if good let me know and I will try to assist you.

Apr 03, 2012 | Projection Televisions

1 Answer

Sony kdf-37h1000. push power button and the green lite comes on steady and i can hear a fan. never gets to a picture or sound. it then sounds like it shuts power off but lite goes from flashing green to...


Hi catfishbob,
You're lamp came to its peak burning life and now its dead that's why you can't power up the unit and the led light keeps flashing. Once the lamp replace with new one your unit will back to normal again. Click this link for the replacement http://shop.ebay.com/i.html?_nkw=KDF-37H1000&_sacat=0&_odkw=sylvania+ld370sc8s&_osacat=0&_trksid=p3286.c0.m270.l1313.
Hope I helped you.
Have a nice day!
Thanks for using Fixya.

Mar 05, 2011 | Sony KDF-37H1000 37" HDTV

1 Answer

I put a new bulb in the tv about 3 months ago. I was watching the tv the other day and turned it off when done. I went to turn it back on the other day and it does nothing, no red, green, yellow blinking...


Try pushing in the reset button on the front panel, its very small and you will need a pin to push it in. Do this while the TV is plugged in, then power it on again see what it does. If still nothing then the FMT board is developing a known fault. You will need to replace the FMT board if reset doesn't work....
Also..
It could be a fan issue, if one of the fans in the TV stop working this will cause the TV not to power up too.
Let me know what you find...
http://tvtechwork.webs.com/

Nov 10, 2010 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

The blinking green lite that wont go off wont allow the tv to come on tv must be reset each time sometime reset works and sometime tv off for days have to unplug from wall for couple days then replug and...


The blinking green lite that wont go off wont allow the tv to come on. We tried resetting the tv it doesn't work Also the tv has been off for days have to unplug from wall for couple days then replug and reset. It still doesn't work. Please help.

Sep 25, 2009 | Projection Televisions

1 Answer

Convergence on my menu is no longer there


You need the service manual, I don`t know about these particular set, but on Toshiba`s, you had to press the menu button on the set and while holding that in, I think you pressed the red button on the remote. This got you into service mode. If the convergence went out while you were watching it, I don`t think adjustments will cure your fault, it sounds like the Driver chip may have failed which drives the convergence coils on the tube necks. Is it just one/two of the colours?? Is it out in the centre?? Is it out around the edges?? If you do intend adjust anything, make sure you write EVERY setting down first including EVERY mode, It is a VERY time consuming job and even then you`ll NEVER get it perfect. You have to repeat the whole setup in EVERY mode, eg: Widescreen, 4:3, Stretch, 16:9 etc. You`ll also need a signal generator to give you a steady picture while performing any adjustments and when you alter the brightness and contrast, this will affect the convergence also. DO NOT alter the binary settings of the set, these tell the micro what the set is fitted with, eg: Nicam, Freeview, NTSC, PAL etc, etc. If I remember correctly, there are about 300 settings which have to be performed in sequence and when you alter one setting in one mode, this can affect another setting in another mode. It`s a real nightmare, believe me. The only trouble is, if you do start to alter the settings and you find that there is a faulty component, You`ve got to try to get it back to the settings that they were before you started your tweeking. If you do alter the binary code settings of the set, then there`s a very good chance that the set won`t come back on. It took me three days to sort one set out once and even then the customer complained about the convergence. Ian

Jul 29, 2009 | RCA D52W23 52" HDTV CRT TV

1 Answer

The tv willnot power up .the light keeps flashing and huming


Check the horizontal output transistor (H.O.T.) next to the flyback transformer. If it is shorted, the switching supply won't turn on.

Dec 05, 2008 | Samsung HCP4252W 42" Rear Projection...

1 Answer

Model D52W19BYX2 RCA


Horizontal output and the low voltage regulators should always be checked first in a set that wont power up. If you need a manual go to http://www.servicemanuals.net/. Be sure to check back if you need some help.

Jan 05, 2008 | RCA D52W19 52" Rear Projection Television

1 Answer

Sony KP-57WS500


the unit needs the convergence ic's replaced and probably a couple of safety resistors.average repaire are about 300 from a tv shop

Mar 04, 2007 | Sony KP-57WS500 57" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...