Question about Hoover Washing Machines

Open Question

I have a hoover vhd9163zd washing machine and it has error E09 on it. The instruction says turn it off and run the program again. The drum wont turn and the damn thing is two weeks out of warrantee any advice on what the problem could be.

Posted by on

6 Suggested Answers

  • 1 Answer

SOURCE: Hoover washer model VHD9143ZD

Have the same problem. Have just looked in the service manual, it reads: Error 9 - Cancel the programme by returning the selector to the OFF position. Select again the programme and press the START/PAUSE button to switch the machine back on.

We recall having this problem with a previous Hoover washing machine and it was solved by cleaning the filter. The service manual recommends you clean the filter once a month. The procedure is as follows:
1) Open the flap

2) Only available on certain models: Pullout the corrugated hose, remove the stopper and drain the water into a container.

3) Before removing the filter, place absorbent towel below the filter cap to collect the small amount of water likely to be inside the pump.

4) Turn the filter anti-clockwise until it stops in the vertical position. Remove and clean.

5) After cleaning, replace the filter and lock by tightening the filter screw. Then follow all procedures described above in reverse order.

Hope that helps :)

Posted on Mar 15, 2008

  • 1 Answer

SOURCE: error code e04 on hoover washing machine

called hoover and they replaced the washing machine

Posted on Jul 28, 2008

  • 193 Answers

SOURCE: error code E03 on washing machine

eo3 water not draining,check for kinked drain hose,check that drain filter is clean

Posted on Sep 28, 2009

  • 94 Answers

SOURCE: Very noisy Hoover VHD9143ZD washing machine - just 2 years old

yes bearing housing get loose in plastic drum. needs drum replacement.

Posted on Oct 29, 2009

Testimonial: "Thanks for confirmation that the drum needs replacing, but this is pretty shoddy workmanship by Hoover that this should go in 2 years from purchase"

  • 41 Answers

SOURCE: Door won't open on Hoover vhd9163zd washing machine

THE DOOR MAY HAVE A TIME RELESE SWITCH CHECK IN MANUAL

Posted on Jan 09, 2010

  • 3 Answers

SOURCE: lg washing machine drum light stays on and wont let me turn the

Solution. Unplug the machine. Hold the power button for 10 seconds. Plug back in. Push the power button and the washer should turn on. Walk away leaving the machine on. When I did this, I came back to find the drum light off and machine would start on command now. Good luck.

Posted on Jan 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoover optima 614 drum wont spin


Either a broken drive belt or a failed transmission.

Jan 12, 2015 | Hoover Washing Machines

1 Answer

Candy washing machine gc4 2d washes for about 15" then stops for 30" (the screen goes black) then on again for about 10" and then stops again.


sounds like overload protection is disabling the machine. it could be caused by a lot of reasons, the only advice I have is to check for a jammed drum, empty machine and see if drum turns freely. best luck to you.

Dec 06, 2014 | Hoover Genuine Candy Zerowatt Washing...

1 Answer

E09 PUMPS OUT WILL NOT SPIN


E09 ON HOOVER WASHING MACHINE WILL PUMP OUT BUT WILL NOT WASH OR SPIN?

Oct 31, 2010 | Hoover Washing Machines

1 Answer

Door won't open on Hoover vhd9163zd washing machine


THE DOOR MAY HAVE A TIME RELESE SWITCH CHECK IN MANUAL

Dec 24, 2009 | Washing Machines

1 Answer

Error code e04 on hoover washing machine


called hoover and they replaced the washing machine

Jul 27, 2008 | Washing Machines

1 Answer

Hoover washer model VHD9143ZD


Have the same problem. Have just looked in the service manual, it reads: Error 9 - Cancel the programme by returning the selector to the OFF position. Select again the programme and press the START/PAUSE button to switch the machine back on.

We recall having this problem with a previous Hoover washing machine and it was solved by cleaning the filter. The service manual recommends you clean the filter once a month. The procedure is as follows:
1) Open the flap

2) Only available on certain models: Pullout the corrugated hose, remove the stopper and drain the water into a container.

3) Before removing the filter, place absorbent towel below the filter cap to collect the small amount of water likely to be inside the pump.

4) Turn the filter anti-clockwise until it stops in the vertical position. Remove and clean.

5) After cleaning, replace the filter and lock by tightening the filter screw. Then follow all procedures described above in reverse order.

Hope that helps :)

Feb 15, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...