Question about Kenmore 46462 Front Load Washer

1 Answer

Kenmore HE2 flashing lights

I have a kenmore he2 and the lights are flashing. I have had this machine for 14 months. called Sears and it is going to cost me 400 dollars. Any suggestion about to fix this machine. Any guidance or directions will be much appreciated. Kenmore HE2 110.46462501 stopped in the cycle with some of the status lights lit, lights around the cycle ring flashing. Restart on 'drain and spin" cycle, pump runs for a period then tops with Status lights 'add garment', 'rinse', and 'add garment' lit. The 'wash', 'spin', 'controls locked' and 'door locked' are not lit.  Cleaned out the pump trap as per suggestion. Found a lot of stuff - change, nails, construction screws and a small gold chain. Removed the pump and checked teh impeller for damage, obstructions. There was also a fair bit of goo in the bellows with the float ball, which I cleaned out. I primed the system with about a gallon of water, then ran 'spin and drain' cycle. Cycle starts by pumping out all the water. The pump then runs (mostly) dry pulsing the remaining water in the drain line, and then ends in the flashing light state. Other cycles behave same. Pump runs, no water is added, and ends in flashing light state. Seems like system senses water in the tank, and tries to pump dry. Failing to detect empty state, it gives up. Any  next step suggestions please? --RRLee

Posted by on

  • Anonymous Mar 26, 2014

    half way through cycle, the machine stops, smells hot and all light flash.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 521 Answers

Did the technician point out wat needs to be repaired

Posted on Aug 24, 2008

  • tech expert12 Aug 24, 2008

    also check for the sensor unit which detects water in the tank.also for more information and cheap replacement parts with fitting procedure can be obtained from a link below:

    www.repairclinic.com

    thanks.keep us updated.



    regards.

    fixya expert team

  • tech expert12 Aug 24, 2008

    pls do rate the solution

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sears Electric Dryer is flashing F01 What is wrong?


The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
You can order a new control board from the Sears PartsDirect website.
http://www.searspartsdirect.com/partsdir...
Here's how to do it: http://media.fotki.com/1_p,wkwdftgtbkdgf...


Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Feb 04, 2016 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

Where can I locate pedestals for my He2 washer and dryer?? I refuse to pay a gazillion dollars for them!! Thank you! And, I don't care if they're used....


Here are the part numbers for the 2 pedestals
10 in. - Sears item 46822 (Used one not found)
&
15.5 in. - Sears item 57822.
($34.00 used)
http://www.consumerdepot.com/products.asp?id=57822R

I would also recommend calling your local appliance recyclers. (usually there is one near any city dump.) There are numerous pedestals in appliance recycling areas.
Another avenue is contact USED appliance dealers. They also have them sitting around. I turned many of these around for resale $40.00 each on machines that were not cost effective to repair.

Thanks for choosing FixYa,
Kelly

Aug 11, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

Need part number for my kenmore he2 plus washer's drain pump. I need to replace it due to a continuing F21 error code msg


Sears has a fantastic part locator on line try that just surf the sears site you ll find it ,probalby even have a number to call just in case

Mar 09, 2011 | Kenmore HE2 Plus Front Load Washer

2 Answers

Frontload washing machine makes noise during spin cycle


call sears 1 800 4myhome they can walk you thru some troubleshooting. First thing pull back the rubber ring between door and barrel to see if anything like pens etc feel into the gap underneath. If not call for troubleshooting. Get a plan with sears then wait 30 days and call in the problem. Fix will cost less.

Mar 22, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore HE2 flashing lights


had an old pressure switch that I thought was the problem I had from something else a year ago
That was the washer not starting, all kinds of lights
I took the back and top off and reconnected all the plugs.
Had a loose connection somewhere, it worked after that.

I blew into it and put it back on.
The rattleing quit in the pump after it pumped out, while the drum was spinning slow.
Now working ok

Nov 24, 2008 | Kenmore 46462 Front Load Washer

1 Answer

Kenmore Elite Oasis HE/ Error Code F1


Sorry to tell you but you have a faulty control board. It is a bad part from the factory. They know that its bad too! They have completely remanufactured the part. There is lawsuit against whirlpool (whirlpool made the oasis) for the problem. Some people have been able to call and complain to whirlpool and got them to pay for the repair. Complain a lot. Good luck. sorry for the bad news.

Nov 20, 2008 | Washing Machines

1 Answer

Control Unit Assembly


We are researching for new laundry machines (10) for our condominium laundry room. I'm glad I found this site, and I guess we won't be buying Kenmore products.

Saratoga Condominiums

Oct 23, 2008 | Kenmore Oasis HE 27082 Top Load Washer

6 Answers

Kenmore HE2 flashing lights


I had the same problem with it stopping mid cycle and lights flashing. Turns out all i needed to do was clean out the very clogged drain pump filter. it is located just behind the front kick panel. it unscrews and pulls right out. there was a nasty accumulation there. ran great afterwards.

Jul 01, 2007 | Kenmore 46462 Front Load Washer

Not finding what you are looking for?
Kenmore 46462 Front Load Washer Logo

620 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Ron Lankford

Level 3 Expert

5386 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

2mikecurtis

Level 2 Expert

65 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...