Question about Whirlpool Duet GHW9150P Front Load Washer

3 Answers

Whirlpool Front Loader Washer Model# WFW9600

It's giving a fault code of F35. Anyone know what this means?

Posted by on

  • 1 more comment 
  • Caserina Aug 25, 2008

    Apparently F35 means the washer WFW9600T has a broken part. I don't know which part yet, but it's being ordered. I'll follow up when I find out.

  • Caserina Aug 29, 2008

    Fault code F35 for a Whirlpool washer/dryer duet WFW9600T means there's a part called a PSI switch that has to be ordered and replaced.

  • cjblkr Sep 02, 2008

    I have the same washer WFW9600. Just got back from a 3 week trip and never had a problem. Put a load in and it stops with F35 code. water and pump and drain seem to be working. Have unplugged and replugged. Have also suctioned the drain hose at the back with a wet vac.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 876 Answers

This code is not on the list.
Try this:
Push cancel twice
Select drain and spin
Select your cycle and push start.

If this does not clear the code, you will need a service call.

Before you do that I am wondering-Are you using an HE detergent and in small amounts? Are you loading the washer evenly- for example towels with towels lingerie with lingerie and jeans with jeans. Front loaders are very sensitive to how they are loaded. Check everything you can:

Turn off the washer and unplug it. Grab some old towels and a bucket.
Check the drain hose- is it twisted, squished or plugged ( you can turn off the washer unplug it and remove the drain hose to see if it is clogged.) While you are back there check the incoming water hoses are they twisted? Unscrew them from the washer and make sure the little filters at the ends of the hoses are not plugged, so that water is coming in freely. Make sure water valves are turned all the way on.

When you are back in front examine the door seal. Is it in good condition? Give the tub a spin with your hand. Does it spin freely and does it feel secure?


Check your dispensers. Are they clean and empty? if they are not try running an empty short cycle with just a little Hot water in the liquid dispensers to see if they are plugged.

Okay. Good luck to you. I hope this can be solved without a service call.

thank YOu for using FixYA Ratings are always appreciated.

Posted on Aug 24, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had a suds error and then a F 35 error. Turns out I had a collection of junk and debris between the door seal and the drain at bottom of door. Cleared out the debris now my washer is running like a top. (washer senses pressure error, thats why I got said error codes)

Posted on Oct 19, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had a suds error and then a F35 error code.
I replaced the pressure switch PS1.
This fixed the problem

Posted on Sep 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does F35 code mean and what to do?


  • Run an empty cycle without using any detergent. Often the fault code displays when too much detergent is used and the detergent sits in the drainage system. A cycle without any detergent is often enough to clear out the buildup.
  • 2 Pull the drain hose out of the standpipe mounted to the wall behind the washing machine. Complete a visual inspection of the hose for any clogs. If you see any, remove the screw that holds the hose clamp onto the discharge pump and then force water through the drain hose with pressurized water from a garden hose. Reattach the hose and then run an empty cycle to see if the code goes away.


  • Read more : http://www.ehow.com/how_11368049_fix-whirlpool-washer-f35-code-alert.html

    Oct 13, 2014 | Whirlpool Duet GHW9150P Front Load Washer

    1 Answer

    F35 ERROR CODE


    had exactly the same thing happen; did you figure it out?
    Would like to know if you had a big fee as won't bother if it is expensive to fix! Thanks Emma

    Jun 16, 2013 | Miele KM 5753 Stainless Steel Electric...

    1 Answer

    I keep getting the error message F35. Can you tell me what that means?


    The Central Control Unit detected a fault in the analog pressure switch but it could also indicate a draining problem. Check the link below to see what you can try to address the problem.

    Troubleshooting Error Code F35 on Kenmore Elite and Whirlpool Duet Washers

    Nov 03, 2010 | Washing Machines

    1 Answer

    F35 failure code


    F35 is a water level error.
    The water level switch (pressure switch) has malfunctioned.

    If you remove the top panel, three screws in the back, you will have access to the pressure switch.

    With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

    If the fault codes return after doing this, you will likely need to replace the pressure switch.


    Also - please be sure to use He soap.

    Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.*(*&^

    Jul 16, 2010 | Kenmore Elite 45986 Front Load Washer

    1 Answer

    What does F35 flashing mean? I own a Kenmmore elite front loading washer and besides it being broke down most of time it is pretty but doesn't work most of the time. This week it is flashing F35, I bought...


    F35 is a water level error.
    The water level switch (pressure switch) has malfunctioned.

    If you remove the top panel, three screws in the back, you will have access to the pressure switch.

    With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

    If the fault codes return after doing this, you will likely need to replace the pressure switch.


    Also - please be sure to use He soap.

    Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.#%&#@

    May 10, 2010 | Kenmore Elite 45986 Front Load Washer

    1 Answer

    Kenmore waher he3k. i want to know the location of


    F35 is a water level error.
    The water level switch (pressure switch) has malfunctioned.

    If you remove the top panel, three screws in the back, you will have access to the pressure switch.

    With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

    If the fault codes return after doing this, you will likely need to replace the pressure switch.


    Also - please be sure to use He soap.

    Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.^$%

    Feb 13, 2010 | Kenmore Elite 45986 Front Load Washer

    1 Answer

    Fault code F35 what is this?


    F35 means: ANALOG PRESSURE SENSOR FAILURE

    If this failure is displayed, there is any malfunction detected by the Electronic Board.
    1. Check if pressure hose is fixed correctly.
    2. Check if the airtrap is not blocked.
    3. Check if the drain hose is not blocked

    Dec 23, 2009 | Kenmore 44102 Front Load Washer

    2 Answers

    Kenmore Elite HE5t Error Code F35


    we have a kenmore HE2 Plus washer, front loader. been getting F28 code for last several months. usually we can push cancel button, and it clears, unlocks the door, we restart and complete the wash. But now it is locked and we can;t clear it. have even unplugged the machine over night, it still will not reset. any ideas?

    May 09, 2009 | Kenmore 3.8 cu. ft. HE3t Front Load Washer

    Not finding what you are looking for?
    Whirlpool Duet GHW9150P Front Load Washer Logo

    1,325 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Whirlpool Washing Machines Experts

    Dan Webster
    Dan Webster

    Level 3 Expert

    8205 Answers

    Mike Cairns
    Mike Cairns

    Level 3 Expert

    3053 Answers

    prem mathew

    Level 3 Expert

    662 Answers

    Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...