Question about Dewalt 7.2-18.0 Volt One Hour Charger

1 Answer

Fuse blown on 9116 charger what amp is it - Dewalt 7.2-18.0 Volt One Hour Charger

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dewalt Master
  • 61,252 Answers

It will be marked on the fuse, it varies with each charger.

Posted on Sep 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it blow controller fuse when key is turned on?


Electrical: Circuits, Relays - SwedishBricks

www.swedishbricks.net/700900FAQ/Electrical-CircuitsRelays1.html
fuse keeps blowing Drills & Drill/Drivers Questions ... - Fixyawww.fixya.com > Forum > Tags > fuse keeps blowingDrills & Drill/Drivers fuse keeps blowing questions and answers. Ask your fusekeeps blowing drill and drill/driver questions. Get free help, advice & support for ...Ryobi Multi-Volt Battery Charger Fuse - Questions - Fixyawww.fixya.com > ... > Ryobi > Ryobi Multi-Volt Battery Charger1423701) and have blown the internal fuse. The label on the charger indicates the input is 120V AC. Question about Drills & Drill/Drivers. 1 Answer ...Remember that fuses can fail without showing signs of an obvious ... remember that suspect turn signal flashers, fuses, bulbs and relays can be ... will be predictable, such as a bad current or ground connection, blown fuse and the like. .... The relay then sends power to all the lock motors (all doors except driver's door).Missing: drills

[PDF]Electrical Safety - Occupational Safety and Health ...

https://www.osha.gov/.../4...

Occupational Safety and Health AdministrationShe has an older drill with a steel housing and a 3-prong plug. ... current. This willgenerally allow enough current to flow so that a fuse will blow or a circuit breaker is tripped, thus turning off the electricity in that circuit. ..... There are three major ways tocontrol power line hazards: 1. ... Install warning signs at driver's eye level.Missing: drills ‎key

Jan 07, 2016 | Drills & Drill/Drivers

1 Answer

Convert Dewalt Charger DE 9116


It is not feasible to convert it internally.

Jul 15, 2013 | Dewalt 7.2-18.0 Volt One Hour Charger

2 Answers

I need a schematic for a dewalt dwg 9116 charger


if its anything other than replacing the cord, it is not considered "repairable" and there are no schematics offered.

there was a recall on this model charger, so a dewalt service center might be able to repair or replace it free of charge.

Dec 05, 2009 | Dewalt 7.2-18.0 Volt One Hour Charger

2 Answers

Charger not powering up, fuse is good?? what the f---?


Internal board fuse checked? This may/may not help?

Makita 1850 battery charger FIX. A friend asked me to check his charger unit which had failed after it had been connected to a portable petrol generator that incorrectly generated 317 Volts AC and not the usual 240 Volt AC. On the charger circuit board next to the transformer wire connection is a component marked F2; this is a 2.5Amp fuse covered with heat-shrink sleeving. This fuse had ruptured/blown. Also blown was Transistor Q1, a ''P'' Mosfet labelled IRF9Z24N and Schottky Diode D9 labelled SR560. Replacing these 3 items got the charger working again. NB Resistor R31 is only 0.1ohm - don't assume it's gone short circuit! NB. I'd presume that most other Makita chargers will have this heat-shrink sleeving ''camoflaged'' fuse on the input of the circuit board and it would definitely be worth checking if the charger has stopped working. Regards Roy

Oct 24, 2009 | Makita 2 Bl1830 18v Battery,dc18ra Charger...

1 Answer

The fuse is blown in the charger. I want to replace it. 4A 125V


Usually when the fuse blows in the charger there is some other malfunction there in the board. The charger for your tool is listed as obsolete to contact the service center, and in doing so ask them for the proper fuse, or replacement charger.

Oct 05, 2009 | Dewalt DC727VA Heavy Duty 3/8 Inch 12 Volt...

2 Answers

Where online can I download a Dewalt 9116 owner's manual?


Go to Dewaltservicenet.com and in the middle of the page at the bottom find the looking for manual box. Type in your model number and it will take you to a page click in the owners manual and download it from there it is 5 pages long. If I have helped you would you please rate my solution accordingly and thank you.

May 16, 2009 | Dewalt Drills & Drill/Drivers

1 Answer

What is the replacement fuse for a Ryobi 18v charger?


The fuse in mine said 4 amp. I have also used. You can use a 4 amp or lower to replace the original one that blew.

Good Luck

Mar 07, 2009 | Ryobi Multi-Volt Battery Charger

1 Answer

I HAVE A DEWALT DC729 18V DRILL


is this a north american model.all i can find is model DC727 & DC728 model. charger model 9116 & battery is DC9096 may work.charger volts 110v ac. if your buying the individual part like batt & chgr its more expensive than buying the whole kit is cheaper. hope i answer your question

Jun 20, 2008 | Dewalt 18 Volt Compact Drill Kit

5 Answers

No Manual?


Online Manual (PDF) For DW9116
http://www.dewaltservicenet.com/documents/English/Instruction%20Manual/630429-00,DW9116.pdf

Dewalt DW9116 Product Recall:
http://www.dewalt.com/us/articles/article.asp?ID=187

Nov 22, 2007 | Dewalt 7.2-18.0 Volt One Hour Charger

Not finding what you are looking for?
Dewalt 7.2-18.0 Volt One Hour Charger Logo

Related Topics:

369 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Drills & Drill/Drivers Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Jim Thurston

Level 3 Expert

669 Answers

Soulvisitor
Soulvisitor

Level 3 Expert

1113 Answers

Are you a Dewalt Drill and Drill/Driver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...