Question about Stoves 27 in. DW60 Built-in Dishwasher

1 Answer

New world wd60

E4 error light as come on now washer won't work [overfill]

Posted by on

  • Anonymous Nov 22, 2008

    Same problem - at same time (1 year after purchase) as guarantee was ending. Engineer "fixed" the problem - and one month later the same error code has appeared and i am unable to use the dishwasher.



    Any solutions? Or recommendations for a 60cm integrtaed dishwasher to replace this one?

  • register114 Jan 02, 2009

    I have the e4 error code too!

    Left machine alone for 3-4days and it worked again for 1 cycle, then e4 error code again.

    Any suggestions?


×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

I made sure drain hose was not blocked found gunk at bottum , but to reset alarm e4 , had to drain dishwasher put it on its side - must have remove an airlock. checked turn on and e4 had gone , all ok now suggest rinse all dishes before washing

Posted on Jun 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have SE showing on my Samsung washer/dryer please respond with any suggestions


Samsung washing machine no workeing ? dL
The door was unlocked while the washer was running
dS
The door was opened while the washer was running
d5
The door was opened while the washer was running
FL
The washer failed to lock the door
Hr
Washer temperature control problem
Heater Relay Failure (on main PCB)
LO
The door will not unlock
5E
Washing machine has failed to drain the water
4E
Water fill time out
ND
Water Does Not Drain From Washer
NF
Water fill time out = No Fill
dE
Washing machine door detected as being open
UE
Washing machine has detected an imbalanced load
DC
Washing machine has imbalanced load and will not spin
3E
Motor fault detected
bE
Motor short error
OE
Washing machine has detected an overfill situation
LE
Water leak - Excessive SUDS - Bad water level switch
HE
Water heating error detected
tE
Water heating sensor (thermistor) error detected
IE
Water level sensor fault
CE
Abnormal water temperature detected
E1
Not filling in allocated time
E2
Pump won't empty - not draining
E3
Overflow - overfilling with water
E4
Out Of Balance (OOB) detected
E5
Water temp rising or falling too quickly
E6
Water temp rising or falling too quickly
E7
Pressure switch
E8
Temp too high on low temp washes
E9
Water leak, Water level has reduced
EA
Motor generator error
EB
Motor error

Sep 30, 2016 | Samsung Washing Machines

1 Answer

My Teka DW7 57 FI VRO2 dishwasher shows the error code E4.


E4 means it is overfilled because of too much inlet water. Turn off the main supply. Remove excess water from the base pan and restart the dishwasher. DW7 57 FI Teka official website Bathroom Kitchen Professional Kitchen and...

Apart from using the manual instructions, you can get technical help from the company directly too.

Hope this helps!

May 15, 2016 | Dishwashers

1 Answer

Showing error code E4


check for waterleaks filling the overflow tray at the bottom of dish washer that is activating the float switch. check for defects or damage at bottom of dishwasher.

Feb 01, 2012 | Bush Dishwashers

1 Answer

Error code FL flashes and my calypso washer keeps beeping. Won't start just shows the code.


FL error - Flood condition

"FL" flashes if any overfill condition occurs. This condition occurs when excessive water in the tub causes the overfill switch to trip. The control must realize that the trip was due to an overfill condition instead of a suds lock condition in order for "FL" to be displayed.

With an overfill condition, the beeper repeats a warning every 10 seconds with no time out. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit. Press STOP/CANCEL to clear the display.

You coudl se this manual: Service_Manual_PDF

Hope this helps.

May 20, 2011 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

E4 fault code


Hi, when a dishwasher goes into overfill mode it usually means that the bottom tray has water in it that operates a float connected to a microswitch. Open the bottom panel and soak up all water then check to make sure the float is down completely.then restart dishwasher. Why it has overfilled is another problem. It could be a faulty pressure switch,pressure switch hose may have a hole in it, water valve may be faulty. Too much soap or wrong soap can cause too many suds and hence overfill.Also if rinse aid is spilt when filling. Or seals leaking. etc.

Feb 02, 2009 | Dishwashers

1 Answer

New World DW60 dishwasher not working originally had E4 fault Power comes into the PCB the switches and led's light up but nothing happens. After about 5 mins there is a short beep. Does not show any...


I f you have warranty on this please call them, you have a defective D/W.Unless there is no charge for repairs ,don't spend a dollar on what is going to be a on going problem ahead.To explain how to fix this is what the manufacturer should have done in the factory and not made 1 dollar off of this defective D/W until it proved this to be ready .What has happened to Quality Control ? Does it no longer matter ? Very sorry ,you should seek a refund ASAP.

Jun 23, 2008 | Dishwashers

2 Answers

Kenwood Slimline Dishwasher KDW8ST2A


I have a Kenwood Kdw8st2a and have been constantly plagued by the E4 overfill error.

Lifting the front of the dishwasher and tilting it backwards seemed to clear the E4 error only for it to come back after the next wash.

I found eventually that the connection to the U bend under the sink was too narrow and was almost blocked hence the dishwasher was not emptying properly.

I disconnected the dishwasher waste pipe and ran the waste into a bucket for about 6 cycles and it worked fine.

Eventually drilled through the kitchen wall and fitted a lower direct waste pipe to the drain. Overkill maybe buit it hasn't done an E4 since.

May 21, 2008 | Dishwashers

1 Answer

Problem with Candy CDI45, Error E4


The instruction manual defines E4 as "overfilled", a possible reason being too much inlet water. What helped with our machine - removed all dishes inside, then let the machine's pump run briefly to make sure as much water was drained from the system as possible. I then unplugged the device, placed a large towel on the floor around its base, and tilted the machine front-ward, until all water had run out. Lifted the machine back upright, plugged it in, switched on - and voilà! it's working as I speak.

Feb 28, 2008 | Dishwashers

1 Answer

DSE DVD/Video rcorder G1927 error notice


I think the stupid product manufactured by Funai has some fundamental material issues that with repeated uses either the laser lens get dirty or scratched. My guess is if it is dirty a lens cleaner would get rid of it but it is a scratch or physical damage it should be repaired. Any help from Funai? Forget it....they should have probably recalled the units once the issue is known but you know how Chinese/third world countries work..

Jan 15, 2008 | Televison & Video

3 Answers

E4 error on new conia dishwasher


Had the same problem. First you will need to tilt dishwasher back 45 degrees and tip out all excess water. A couple of towels on the floor are a good idea.

Second check that the little nozzle on the elbow under your sink where your overflow attaches is drilled out.

This fixed my problem after fussing around for a day and I was starting to disconnect everything to take it back.

Sep 15, 2007 | Dishwashers

Not finding what you are looking for?
Stoves 27 in. DW60 Built-in Dishwasher Logo

Related Topics:

1,430 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stoves Dishwashers Experts

Owen Barnes

Level 3 Expert

867 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

 Russ Hill
Russ Hill

Level 3 Expert

2183 Answers

Are you a Stoves Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...