Question about Zenith E44W46LCD 44" Rear Projection HDTV-Ready Television

7 Answers

Lamp timer near 10K

Ok, I ordered a new lamp, but I can't figure out how to reset the light timer. I go to the service menu, and then to replace lamp. It shows listing for several (0-9) bulbs and a total, only bulb 0 has time listed (this is the original one for the tv). It only highlights the total and a section at the top that says "lamp use time reset". I press the center button of the navigation circle, and the menu dissapears, but nothing happens. While in this menu area, I cannot make the highlight move at all. Is there a code that I should be typing in, or when I replace the bulb will it recognise it as a different one.

p,s, I removed the old bulb, and put it back in to see if there was a switch that would reset it.

Posted by on

  • 2 more comments 
  • Fireman Ed Aug 23, 2008

    manual shows nothing on resetting this timer. This is in the service menu area.

  • Fireman Ed Aug 23, 2008

    the manual says nothing about lamp timer resetting. it just tells me that the orange light on the tv means replace bulb because of timer.

  • Fireman Ed Aug 23, 2008

    it has the original bulb still, I have tried holding the enter button down for a minute at the "lamp timer reset" prompt, but no dice so far. anyone else?

  • Fireman Ed Aug 23, 2008

    thanks, this was exactly what I needed to get the light out on the tv.

×

7 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Zenith Master
  • 19,396 Answers

"If you replace the DLP lamp out of your Zenith or LG, you will need to reset the counter…otherwise you may get an annoying reminder every few days if you’re surpassed the predetermined hour mark.
To Reset:
Ensure the TV is powered on.
1) Press and HOLD the MENU button on the TV
2) Press and HOLD the MENU button on your REMOTE
(hold both these until the service menu pops up 5-10 secs max.)
3) Let go of the REMOTE button first, then release the button on the TV
4) Press and HOLD the ENTER (or OK) button on the TV
5) Press and HOLD the MUTE button on the REMOTE
(hold both until the LAMP LIFE HOURS appears on the screen)
6) Let go of the REMOTE button first, then release the button on the TV
We suggest writing your lamp hours on a peice of masking tape and taping it to the back the TV for future reference.
7) To reset the lamp counter, press SELECT (or the button in the middle of the direction arrove buttons). Hit SELECT a second time to confirm clearing the lamp counter"

From
Reset Your Zenith or LG DLP TV Lamp Counter
Do not forget to vote the best solution.

Thanks
"

Posted on Aug 23, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,268 Answers

Hold the navigation keys at the same time for 20 seconds

Posted on Aug 23, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 157 Answers

Ok. Turn TV off and leave it off for a couple of hours.
Take the lamp out. Turn TV on and then off.
Again keep it off for a couple of hours.
Inset the lamp back in and turn TV on.

Now:
Entering the service menu --> press Menu on TV and remote simultaneously for 5 seconds

For details on how to use the service menu click here

Hope that helps
JigSaw
Fixya Team

Posted on Aug 23, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 623 Answers

Use bulb made for your brand of set

Posted on Aug 23, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 505 Answers

Hold Down The Reset Button For 60 seconds
Thats what i had to do mate

Posted on Aug 23, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,071 Answers
  • LORETO LACARON
    LORETO LACARON Sep 02, 2008

    Did the solutions from all of us experts solved your problem if not then let us know the current updates so all the fixya experts can assist you further.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 848 Answers

Just go through the manual it will guide you to solve your problem..........

Posted on Aug 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vizio HDTV won't turn off cc. Menu-setting and more, I can choose any of options but not on cc. All of them have highlight name but cc is not highligh and I can't use to turn off cc,suddenly appears.


Do a reset to this TV. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Jan 10, 2017 | Vizio Televison & Video

1 Answer

I HAVE AN AKAI HD TV DVB-T32W. When I started out first time, it autoscans but found no channel. press DTV or ATV, it,says "No channel. need to rescan". But nothing happens, thanks


Main system control memory IC fault. This is a very small IC; have 8 solder terminals, and can be located very near to the main system control-chroma IC. Check and replace it. Be sure to replace it with the same number printed on it; in all respect. Otherwise, it won't go. http://electronicshelponline.blogspot.com/ Before replacing it, try a reset to this set, and then check.
There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here.

Jan 09, 2017 | Akai Televison & Video

2 Answers

My samsung smart tv hdmi ports do not work anymore


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Jan 09, 2017 | Samsung Televison & Video

1 Answer

Truetech 10 inch under the counter tv is stuck on channel 2. I need 3. Channel buttons on tv & remote do not change 2 to channel 3. Unplugging, Resetting hasn't worked Any ideas?


Main system control memory IC fault. This is a very small IC; have 8 solder terminals, and can be located very near to the main system control-chroma IC. Check and replace it. Be sure to replace it with the same number printed on it; in all respect. Otherwise, it won't go. http://electronicshelponline.blogspot.com/ Before replacing it, try a reset to this set, and then check.
There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here.

Jan 08, 2017 | Televison & Video

1 Answer

My sh100 is stuck on the menu screen when you turn it on


Do a reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Jan 08, 2017 | Televison & Video

1 Answer

Black screen, green light on the bottom is on, electric plug is on house plug, no picture, was working fine last night, now only black screen!


Do a hard reset to this set, and then check. If it do not help you, check and replace its main digital board. It will be faulty.
There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Jan 08, 2017 | Televison & Video

1 Answer

How to reset lamp timer on panasonic pt-50dl54j


If you wish to get some details; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Jan 07, 2017 | Panasonic Televison & Video

1 Answer

Do a 2001 GE projection tv have a lamp in it?


Yes course there is a lamp . You can order one from ebay for around $10 .

Apr 21, 2014 | Televison & Video

Not finding what you are looking for?
Zenith E44W46LCD 44" Rear Projection HDTV-Ready Television Logo

413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zenith Televison & Video Experts

The Knight
The Knight

Level 3 Expert

71608 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2291 Answers

Are you a Zenith Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...