Question about Projection Televisions

1 Answer

Pioneer Elite Plasma TV won't turn on, acts like not getting any power, but other components on the power strip have power. Is there a reset switch other than the power on/off on the back?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

No you need to take it to a repair shop and have them fix it..you may have blown caps and they may need to be replaced

Posted on Aug 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pioneer plasma elite pro-504pu how do reset to factory mode on standby mode >??


hi,
u cam reset ur only by the following way.

p { margin-bottom: 0.21cm; }

In order to enter Service Mode, TV guide must be turned off

In order to do this procedure you must have and use the correct remote. The full function remote that

came with the set has a TV Guide Logo in a red box. This is the remote you should use.


NOTE: If TV guide has not yet been setup, then the 1st step is to follow instructions to set TV guide up.

Enter ZIP code, cable or ant. Etc.



1.press and release the "TV Guide". TV guide will appear on the screen.

2.Navigate to the TV Guide tool bar and use the ">" button to select "setup" in the menu and press

and release the "enter" button

3.use the "arrow down" button to select "default options"

4.press and release the "enter" button and select "general defaults"

5.press and release the "enter" button (opens menu on lower left side)

6. use the "arrow down" button to select "auto guide"

7. use the ">" button to select "off"

8. use the "arrow down" button to select "done"

9. press and release the "enter"

10. press and release the "TV Guide" button to turn the display off



System Reset Using Service Mode:



1. Enter Service Mode

2. Use the "muting" button to select "initialize" screen

3. While on the "initialize" screen

4. Use the "down arrow" button to select "final setup"

5. Press and release the "enter" button to select "data reset"

6. Use the ">" button on the remote to select "yes"

7. Press and hold the "enter" button until the screen goes black release "enter" button on remote.

8. Power the unit off using the remote control

9. Unplug the power cord from the media receiver to complete the reset

10. Plug in the media receiver; turn the system on and reset is complete.


ok

Jan 11, 2011 | Pioneer Projection Televisions

4 Answers

I have a Pioneer Elite PRO-940 - problem exists when the tv is powered off - a component (might be a power supply or transformer) kicks on within a second or two after being turned off - emits a low...


Hi-
Do you have a receiver attached to your devices? make sure that components are as well of since its creating a background noise on some devices, check the cables as well.

Thanks for using fixya, keep us posted for any progress.

Jul 16, 2008 | Pioneer Projection Televisions

2 Answers

Pioneer elite tv turns off from a pop sound and manual says-will


It is most likely the power supply. Do not try to fix this yourself. There are LETHAL voltages inside such a TV, which can persist for WEEKS after it has been turned off.

Jan 09, 2010 | Pioneer PRO-710HD 64" Rear Projection...

1 Answer

I have a pioneer elite plasma (Pro-1540HD),and my color settings are completely screwed up.(my kids and father-in-law were messing around with my remote.). I've gone through the manual and done everyhting...


Start with page 51 in the manual, disconnect all external sources(vcr,dvr,cable box,etc.) start the tv with just the cable from the wall jack straight to the tv. make adjustments as needed.when you have a satisfactory picture, reconnect the external sources one at a time and see if the picture changes after the addition of each component, if it does, the problem is probably that component. good luck.
Marc

Sep 13, 2008 | Pioneer Projection Televisions

4 Answers

Problem with pioneer elite pro-99


your tv's hardware might got the problem. this should fix with an expert technician that they have a tools for fixing this problem. if repairing will cost you alot then i suggest that you have to buy a new tv insted of repairing your old tv. hope that helps!


CHARCOIS

Aug 21, 2008 | Pioneer PRO-99 TV

1 Answer

Problem with pioneer elite pro-99


We are having the same problem of the Pioneer Elite Pro-99 turning itself off all of a sudden. The red 'non' power button comes on as if we had turned it off remotely.
We would love to resolve this. If you can help let us know.

Jun 30, 2008 | Pioneer PRO-99 TV

2 Answers

Pioneer PRO-510HD Elite


since your tv is 6yrs old it could be that the video circuit has cold solder that needs to be resolder if that does not work then a focus on the video circuit by replacing the component there, it could be an ic or transistors or diode.if you are not a tech get one to look at your set.good luck.for further help email me at nicodhem@yahoo.com

Apr 06, 2007 | Pioneer PRO-510HD 53" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...