Question about AEG Lavamat 72640 Front Load Washer

2 Answers

AEG WASHING MACHINE

PLUMING IN SECOND HAND MACH (AEG)

HOW CAN I TELL HOT & COLD ON MACH TO PLUMB IN??

Posted by on

  • DAM123 Aug 22, 2008

    help wanted

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,462 Answers

Fit hoses at random. put on a rinse cycle. if cold water comes in then hoses are correct. if hot water comes in, then reverse hoses

Posted on Sep 07, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to remove and refit carbon brushes on AEG lavant 610
Thank you

Posted on Mar 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the filter for die AEG lavamat 538 washing machine and how do you clean it?


Hello,

The only filter/screen I am familiar with is the one in the hoses the supply hot and cold water to your machine. They should be checked once in a while but I have never found much in them.

However, the manual for your machine is located here:
AEG OKO LAVAMAT 538 Operating Instructions Manual

Best wishes,
Joe

Aug 24, 2016 | AEG Washing Machines

2 Answers

Hot water not coming into washing machine


The solenoid valve that lets hot water into unit is not opening. Check out the valve itself and the timer cam that feeds power to the cam.

Jul 04, 2015 | Maytag Washing Machines

1 Answer

What does E50 flashing on a Aeg washing machine


Your Water inlet valve is bad or has failed! You need replace either Hot or cold valve.

Jul 25, 2014 | AEG Washing Machines

1 Answer

Washer not filling with water


Hi Karen. Problem may be the internal "tap" that operates electrically. First test - If you are trying for a cold wash, try a hot wash. If maching begins to fill you know this tap is your problem. There are 3 solutions if this is the case
1) swap hot and cold water hoses at the tap and tell machine to do a hot wash - only good if you only want cold washes
2) check where hoses connect to machine at rear - sometimes a fine mesh filter that has become clogged - may be at either end.
3) Replace the internal "tap"(solinoid). This "tap" has a rubber diaphram inside that may become stuck if the machine has not been used for a while. it can be easily dismantled and reasembled by a handyman.

Apr 07, 2014 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Even when the machine is set to cold it pulls in hot


not sure on that one most machines are cold fill now,,think it is to do with the valves been closed , even though the machine is in a cold wash it registers a fault when any of the valves are closed

Nov 10, 2013 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

No cold water is comming out of the cold water pipe, when I press warm/cold only the warm water comes out what could be the problem?


hi sounds like u could have self pluming taps on your hot cold pipes common for them to get blockd due 2 hard water need 2 replace taps or remove and clean holes out in old taps hope im right from washerman27

Apr 27, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Washing maching won't rinse in cold water


hi is this hot and cold water piped machine? ie two connections on rear of machine for hot and cold pipes ? if so are your pipes connected properly on machine and the water supplies? if cold supply is connected to hot supply then wash inlet allows water in washer then washes in cold? but when rinse is due? the elec valve that has hot water pipe connected?? is failing to open allowing water flow of hot on rinse so advise recheck pipes for flow of water from both? when disconnected from machine if flow ok then possible valve blocked/faulty hope you can understand above? if you can give more info on your machine it would help to offer a remedy?

Nov 01, 2008 | Hotpoint Washing Machines

1 Answer

Plumbing


it depends if you have the connections already there. If not then you can make a tee branch from the hot and cold pipes running to your kitchen sink. Then solder 2 15mm branch pipes. this will now be your hot and cold feeds to your machine. At the end of the branches attatch a washing machine valve (red for hot, blue for cold. You can now attach the hoses from the machine to the valves you have just fitted. Really easy

Sep 15, 2008 | Zanussi FJS1225W Front Load Washer

2 Answers

Washine machines


Yes. There is a part that allows you to connect the cold water supply to both the hot and cold inlet hoses. It has worked successfully on our 6100 for 8 years or so. I think it was part of the original kit rather than a subsequent purchase - it's a Y-shaped yoke with an inlet connection and two outlets that accept the two hoses feeding the inlets of the machine. From memory i tink the situation is mentioned in the user manual somewhere.

Jun 10, 2008 | AEG Lavamat 72640 Front Load Washer

1 Answer

Fisher and Paykel MW051 washing machine.


If you can stop it with your thumb there is NO DOUBT it is water pressure.. Pull the hose and check the tap direct, that will tell you if you have a plumbing problem of just a funky hose...
Good luck

May 08, 2008 | Fisher Paykel EcoSmart GWL15

Not finding what you are looking for?
AEG Lavamat 72640 Front Load Washer Logo

Related Topics:

398 people viewed this question

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...