Question about Pioneer Audio & Video Receivers

1 Answer

Aux wont work - Pioneer Audio & Video Receivers

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 108 Answers

Make sure that "AUX" is turned on on the menu. Some Pioneer radios have a front aux, a rear aux, a rear steering wheel control jack, and an aux through the IP-BUS only. First, make sure that if there is an auxillary port on the back of the unit, that it isn't the steering wheel control plug by accident. Second, front auxillary inputs on Pioneer radios NEVER need to be turned on in the menu, only inputs on the back. Any back inputs are turned on in the main set-up menu when the radio is first turned off. Hope this info helps.

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get aux cord to work on PD-103 to work. Its hooked up to a pioneer vsx-5045. Normally my dad would do it but hes un reachable


you need this



26185313-4ip34bcykcozxbw5dk1m1db0-3-2.jpg
rca red and white goes at the back of your amp or receiver. look for a free slot ( cd, dvd or aux) and there, you have an aux cord.

May 05, 2016 | Pioneer Audio & Video Receivers

1 Answer

Reciever


You should not have to specifically plug a servo into the AUX for binding. try a dif. receiver to see if it works.

Sep 18, 2014 | Audio & Video Receivers

1 Answer

When i use the aux. mode the right speaker does not work but the left does, but when i use the radio the right and left speakers work just fine.


I just looked this particular model up on several different sites. Ebay is offering refunds on them. I found other sites that went into great detail on this model. Some people had to remove face plate then the problem seemed to get better. If your aux cable is not new. As a DJ I would suggest putting a light coat of WD40 on a paper towel or napkin makes sure just very light coat on cable insert and twist see if port is dirty by wiping when you remove aux cord. DO NOT re connect for play until allow time to dry. Others can't get SD to work. You also may want to double check the wiring on right side just to make sure there is not a break of crack somewhere between aux and right side connection. That's my basic troubleshooting process.

Apr 13, 2014 | Pyle Audio & Video Receivers

1 Answer

AUX


first test you stereo's inputs using another sound source like a cd or dvd player, plug in to the tape or aux inputs on your stereo. if it does , work then check the cable from your phone to the stereo maybe faulty

Dec 10, 2013 | Audio & Video Receivers

1 Answer

Yamaha yas-101 uverse codes


I had the same problem with my U-verse s10-10 remote and a yamaha SR 300 soundbar. Here is how I got my volume control (but NOT power control) on the yamaha working:


First - always send volume control to the AUX button:
Press and hold AT&T key and OK for 1 second, release, look for 2 flashes.
Now press AUX button. The AUX button will show a long flash.

Second - Go through the manual programing steps listed in the guide for the AUX button (hold AUX and OK for 1 second, release; 2 flashes, punch in code). But instead of pressing the Power button to try to turn off your yamaha soundbar, press the volume up / down and Mute button. I think the code that worked for me was 4045 but I honestly don't remember.

The key is that you have to send the volume control to the AUX button first or it's all a wash.

Jun 26, 2012 | Yamaha YAS-101 Front Surround Sound Bar...

1 Answer

The plug works because the socket switch is turned on and the volume control button is green but when I plug in the auxiliary cable there's no sound? Is there something wrong with the inside of the...


Was the second aux cable you tried new or old? If both aux cables were older, you might possibly want to try (not necessarily buy) plugging in a new one. If you have done that: How old is this receiver? Brand new or older, if older it could be build-up inside the jack causing a break in the connection between jack and aux cable. If this is the case then a simple cleaning with a Q-tip and some alcohol could help immensely. If that's not the case, it sounds like you could have a short in the jack.

Jul 13, 2011 | Audio & Video Receivers

1 Answer

Problems with sound from AUX. WHen choosing AUX music starts and then stops after a few seconds. Why ?


What is the source that youhave fed to the AUX. make sure that the source is not stalling the music, or the source button is tripping off. please recheck if the amplifier is working fine otherwise.

Sep 23, 2010 | Audio & Video Receivers

2 Answers

Need a code for my Comcast Universal Remote


30176 is the code you need . Press Aux and then hold setup until Aux lights up. Enter code. If you want the remote to control the receiver all the time, press Aux and then hold setup until Aux lights up. Enter 993 then press Aux. Aux will flash, now press Cbl and Aux should light up when you use the volume.

Jun 16, 2009 | Yamaha RX-V463 Receiver

1 Answer

Radio AUX missing


If you can give me the model, I can do some research for you :)

Apr 06, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

428 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio & Video Receivers Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1128 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Pioneer Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...