Question about Black & Decker Classic Metal APP F63D Iron

1 Answer

I want to repair myself

Cord shorted out exactly two days after the warranty expired and store would not take it back. How do I exchange the cord myself.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 235 Answers

There is a security screw in the back of the F63D classic iron. It must be removed to get the back plate off. I haven't found the right tool yet myself, though it was suggested it is a "security" Torx.

Posted on Aug 23, 2012


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: cord short ccircuit

The back comes straight off. All you need to do is take a small screwdriver and pry against the bottom metal piece, then it should start to come off. Make sure you take it off carefully so as not to break anything. Pry evenly all around the plastic end cap until it comes off.

After that, you can replace the cord. It's connected via two crimp caps. Easy to replace. Just make SURE you purchase a cord rated for an iron.. DO NOT clip the plug end from an extension cord or similar and use it. The iron uses 16 gauge HEATER CORD. Easy to find, but you could melt your power cord and possibly cause a fire if you don't replace it with the correct type.

Posted on Mar 16, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fix Rowena iron with retractable cord

I would contact a small appliance repair business near you, they can supply the needed cord and the repair for very little money I would think

Sep 23, 2016 | Irons

1 Answer

Electric cord is working sometimes

You have a short in electric cord. If you choose to replace cord be sure to replace the entire cord. Do not attempt to repair a damaged cord as this may present a fire hazard.

Jan 27, 2014 | Sunbeam Irons

1 Answer

Replace cord

yes you can change it or you can also take some repair.

Jan 19, 2014 | Panasonic NIA56NR NI-A56NR Iron

1 Answer

Cord has a short in it

You'll have to remedy or better replace the cord. Just buy similar to hardware store and put it to your iron. It's simple to replace and you have to have a analog tester to be able to test the cord without plug-in to AC wall voltage.
Thanks for asking.

Jul 15, 2011 | Euro-Pro Shark GI490 Iron

1 Answer

My Pro Finish 714 cord was accidentally cut. Is it worth replacing the cord? Where do you get a new cord and can I replace it myself?

Thank you for using FixYa. Is the cord cut near the iron end or the outlet end? could the cord be shortened? A new cord can be purchased at most reasonable hardware stores and with a little care and attention can be replaced yourself.

Hope this has been of some help.

Mar 04, 2011 | Black & Decker ProFinish X750 Iron

1 Answer

Broken iron cord need an iron repair person?

Depends on warranty stipulations, mainly, and finding someone who knows how to do it. Doesn't hurt to ask if the appliance guy can do the job.

Jul 15, 2010 | Yamata Gravity Professional GSI-8800 Iron

1 Answer

My dog chewed the cord to my Rowenta Iron

Yes, but not warranty covered.
Check your local yellow pages (yes, printed book) for an apliance repair shop (look for discount coupon in back while you are at it).
Does not have to be an "authorized" Rowenta shop ($20). Get an 8 foot cord if you think you need a longer cord.

The dog can be fixed, too: (I couldn't resist typing that) Wipe some "training spray (pet shop or WalMart $5)" (harmless to dog & environment) onto the new cord (NOT ON THE DOG) to train the dog to leave it alone.

Sep 21, 2009 | Rowenta DX6700 Iron

1 Answer

Shark GI495N cord sparked and burst into flame

shark website for instructions and number

May 07, 2009 | Euro-Pro Shark GI490 Iron

2 Answers

The cord on my professional Luxe has a short near the handle.

Take your iron to a hardware store and they should be able to guide you to the tool that you will need.

Feb 13, 2009 | Rowenta Professional DM890 Iron with Auto...

Not finding what you are looking for?
Black & Decker Classic Metal APP F63D Iron Logo

Related Topics:

378 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Irons Experts

Hjalmer Lamminen
Hjalmer Lamminen

Level 3 Expert

552 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Oloyede Monsuru

Level 3 Expert

1417 Answers

Are you a Black & Decker Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides