Question about Washing Machines

1 Answer

Water keep flowing out while the tub got filled

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 351 Answers

Raise the drain hose higher than the water level in the machine

Posted on Aug 27, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag performa dishwasher, model # PDBL390AWB.


Sounds like to me you have a water restriction somewhere. Double check and make sure that the main water valve coming into your home is fully open. Make sure the water shut off valve(s) going to the dishwasher both have adequate water flow and that means testing them before being connected to dish washer. If that checks out okay, possibly the plunger that opens and closes in the electric water solenoid is sticking and not opening up al the way since the unit has been in storage for all that time. Sometimes tapping on it when it is in operation can free up that sticking plunger and you may get full water flow restored again. If not, solenoid may have to be replaced. Hope this helps out.

Mar 09, 2014 | Dishwashers

1 Answer

Indesit 657w


CHECK TO SEE IF THE DRAIN HOSE IS RAISED ABOVE THE REQUIRED HEIGHT. IF THE WATER IS OVER FLOWING THE TUB THEN IT IS USUALLY THE A BLOCKAGE IN THE PRESSURE SWITCH HOSE, OR SOME INABILITY OF THE WATER LEVEL SWITCH TO MEASURE THE AMOUNT OF WATER IN THE TUB.

Dec 23, 2013 | Washing Machines

1 Answer

Hot water keeps filling tub and does not quit


the washing machine is designed with a timer limit switch have the switch checked.

Oct 19, 2012 | Samsung WF448AAW 4.5 cu. ft. Front Load...

1 Answer

THE FLOW OF WATER IS ON ALL THE TIME IT JUST KEEPS ON FILLING


There are height sensors attached to your outer tub that should sense the level of the water in the tub. So the lowest sensor would be the problem OR it could be the water level switch.

Jul 17, 2011 | Washing Machines

1 Answer

Gcxrpo9odoww GE washer .. On fill up, it over flows onto floor?


Fill switch could be bad, or fill tube could be plugged making water not stop and it keeps filling. The fill tube goes from fill load selector switch to bottom of tub. Remove from top and blow it out. If this doesnt work replace water load size selector switch.

Jan 17, 2010 | GE WBSR3140DW Top Load Washer

1 Answer

Hot water stream when tub fills & how full tub gets super wash


there should be a knob connected to your water lines that come from the wall, turn the hot to the left.

Jun 22, 2009 | Estate Washing Machines

1 Answer

When you turn it on keeps filling water and it over flows , second problem some times when it runs it keeps running to all the cycles never stops tell you manually stop it


Find the tube from the tub to the water level switch. Remove the tube from the switch and blow the sand and stuff out the line. Pump out any water in the washer and restart. 6b0c2cb.jpg

May 16, 2009 | GE WBSR3140DW Top Load Washer

1 Answer

Water keeps flowing does not stop---does not go thru cycles


You probably pinched the water fill hose that comes up from under the tub when you closed the cabinet. Also make sure it is free from trash in the bottom of the tub and that it is tightly connected to the water level switch.

Jan 06, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore washing machine 80 series


check for kinks in the pipe or restrictions to the flow in the pipes before it gets to the washer, if all is ok then check the filter on the outside of the water connector on the machine for dirt

if you confirm all is clear and the flow of water is not the problem before the machine, replace the cold water solenoid

Oct 14, 2007 | Washing Machines

1 Answer

Water keeps going and going and going!


the water is draining back to the ocean. The drain hose was not emptied properly from its last use. Put the machine in spin cycle (about 5 minutes) only to spin out the water from the outer tub completely and retry washer. If still problem, then visual check drain hose that it still has a "rising" section higher in altitude than the water level of inner tub (when working properly) before it makes a U-turn downward to send back to the ocean. You can also test the drain hose by putting machine in fill mode and crimping off the hose (fold hose over) to simulate a good drain hose. At this test, you should not "feel" water running through the hose if successfully crimped.

Jun 21, 2007 | Estate TAWS800JQ Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

71288 Answers

Brad Brown

Level 3 Expert

15220 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...